GE Multilin EPM 2000 Series Скачать руководство пользователя

Страница: 20 / 52

GE Multilin

Sub Meters

2.2. Setup (Program)

The Meter must be Set (programmed/configured) to match the application settings, before

use. Otherwise, the readings will be wrong. All the Setup values can be re-programmed at any

time, upon entering “SET” However, the settings: Sys (Star/wye or Delta), Vpri, Vsec, Apri,

Asec critically determine the scaling of measured readings. While the scaling may be used to

tune out Instrument Transformer errors, wrong settings will upset the readings of running

systems. It is the user’s responsibility to ensure that only qualified personnel correctly Set-up

the Meter.

Action

Display

Remarks

From the “RMS” or “INTG”

page, go Up

Then go Left .

"Code

" is displayed. “

blinks.

Prog

"Code

The meter is about to enter the Main Menu. “

" blinks.

To proceed with Code Entry, we need to enter the Main

Menu.

•

Go Left .

Or,

to abort and re-enter RMS:

•

Press .

Or, to only view setup, (no edit):

•

Press or to toggle “

” to “

•

Press to enter Main Menu.

•

"Fail" is flashed, then "run" is displayed.

To proceed with Code Entry: "000

" The

blinking

digit indicates the cursor.

The code is Factory Set to

1000. Press to enter each

digit. Three times totally.

000" We have now entered the Units, Tens and Hundreds digits.

The Thousands digit needs to be changed from 2 to 1.

Press to decrement “

000" Now the Code of 1000 is almost in.

Press to enter the Main

Menu.

0000"

“Pass”

“run”

Or,

“Fail”

Notice that a “0” quickly hides each code-digit you enter.

“run” indicates a successful entry into the Main Menu.

Congratulations!

If you were not successful, don’t despair; you can have

another go from the top of this Table! Briefly switching off

the Meter will easily return you to the RMS page, the starting

point.

Now press

Again press

“CLR”

“SET”

You are at the Setup page.

Press to get into “SET”

“2000” You’ve now entered the Setup Menu. The first two entries are

the Model Number and firmware version for easy

identification.

Go to see other Settings.

Go to see and change their values.

Once you’re done, re-trace

your path: and .

Remember “Save Y”

“run” You’re now back to the top of the Main Menu. Go . You’ll

see RMS. You can now go or to view all the display

pages.

Содержание Multilin EPM 2000 Series





















































Результаты поиска

Содержание Multilin EPM 2000 Series

Отзывы:

Похожие инструкции для Multilin EPM 2000 Series

Бренды по названию

Популярные бренды

GE Multilin EPM 2000 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Multilin EPM 2000 Series

Отзывы:

Похожие инструкции для Multilin EPM 2000 Series

Бренды по названию

Популярные бренды