GE Multilin EPM 2000 Series страница 8 Скачать руководство пользователя

Страница: 8 / 52

GE Multilin

Sub Meters

1.2.2. The Keys

Operating the meter is easy using the five keys to take navigate through the

Keypad Operations

Table

. The Display Pages “expand” as you go right, much like the directory or Explorer “tree”

displayed on any computer.

The display shows where you’re headed.

Table 1-5: The Keys

Right Key:

•

forward

into sub-parameter pages.

•

During Edit Setup values, select

next

(right side) digit.

Left Key:

•

The Opposite of the Right key.

•

Back

towards the Main Parameter Pages. Going Left past “Prog” requires Code

entry to enter Main Menu (Setup and Clear)

•

During Edit Setup, selects

previous

(left side) digit

•

Exits from Edit mode, back to the Main Menu.

Up Key:

•

Scroll

thru other Display Pages at the same level.

•

Continuous pressing for 3 seconds initiates

limited Auto-scroll

(

within the same

group of pages

). Press any key to return to Manual scrolling.

•

Increases

the value of the blinking digit during Edit. Typically while changing the

Meter Setup settings.

Down Key:

•

The Opposite of the Up key.

•

Scroll

Down

thru other Display Pages at the same level, thru

all functions

•

Continuous pressing for 3 seconds initiates

the Full Auto-scroll mode

, thru all

functions. Press any key to return to Manual scrolling.

•

Decreases

the value of the blinking digit during Edit.

TURBO Key:

•

The

TURBO

key scrolls thru the following pages:

RMS (Home page)

VLL, A,PF VLN,A,F VA, W, VAR W,VAR, PF PF1, PF2,PF3 , VAh and

Wh. This gives simple one-touch access to the most commonly used parameters,

even for unskilled operators. “One Touch” does not operate in the Setup (Program)

Mode.

•

If you’re lost, the TURBO key is a quick way to get back to the RMS home

page.

•

Continuous pressing for 3 seconds initiates

Auto-scrolling

through the above

Favorite pages.

The parameter name is displayed every 9

second for 2seconds, as well as the first time you press

a key.

At this point you can scroll to the next page you want to see. If you’re not sure which page

you’re watching, one press of any key will immediately identify the Name. The second key

press takes you to the next page.

The Meter Menus and Displays are organized as below. Navigating with the EPM 2000 is very

easy and intuitive. For full details, see the

Keypad Operations Table

. The left-most column

(RUN, CLR, SET) constitutes the “Main Menu

”.

Press the key in the direction you want to go

Display shows where you’re headed.

Содержание Multilin EPM 2000 Series





















































Результаты поиска

Содержание Multilin EPM 2000 Series

Отзывы:

Похожие инструкции для Multilin EPM 2000 Series

Бренды по названию

Популярные бренды

GE Multilin EPM 2000 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Multilin EPM 2000 Series

Отзывы:

Похожие инструкции для Multilin EPM 2000 Series

Бренды по названию

Популярные бренды