GE Multilin EPM 2000 Series Скачать руководство пользователя

Страница: 21 / 52

GE Multilin

Sub Meters

2.2.1. Editing the Setup

First, take a look at the

Keypad Operations Table

. Locate the Shaded, Bold display pages

below.

To enter “SET” and change a Setting value, the sequence (shown below) is: 1, 2, 3, 4. Along

the way, the following must be observed:

•

The Password Code must be entered to change the Setup. The code offered will read

“0000”. Edit ( , ) the blinking Digit to achieve “1000”. Press when done with each

digit, to keep moving towards the “RUN” page. The Meter accepts each digit entered, but

masks it with “0000” so someone watching doesn’t steal the password.

After changing the desired Setup values (Step 4), the sequence to get back to the RMS page

is: 5, 6, 7, 8.

•

Exiting Setup requires you to Save the settings (Step 6). “SAVE Y”, press .

To Discard the changes, toggle Up or Down to get “SAVE N” before pressing .

•

Going forward from 7 (RUN) to 8 (PROG) does not require any Code. You go ,

straight through.

•

Entering into the setup on power up

1.1.1 During power on, press the

Turbo

key continuously for 2sec and displays SET.

1.1.2 Press the

key. Displays the desired value to be changed.

1.1.3 Follow the above procedure.

Figure 2-2a: Entering and Exiting Setup

Password

Prog

RMS

RUN

CLR

SET

Code

1000

Main

Name

Setup

Value

New

Value

Enter the New Value.

Save

To Prog Mode

To Run Mode

Code Entry

Legend Use orkeys

Use orkeys

Use key only

EPM 2000 v03.01.01.00

Содержание Multilin EPM 2000 Series





















































Результаты поиска

Содержание Multilin EPM 2000 Series

Отзывы:

Похожие инструкции для Multilin EPM 2000 Series

Бренды по названию

Популярные бренды

GE Multilin EPM 2000 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Multilin EPM 2000 Series

Отзывы:

Похожие инструкции для Multilin EPM 2000 Series

Бренды по названию

Популярные бренды