GE Multilin EPM 2000 Series Скачать руководство пользователя

Страница: 6 / 52

GE Multilin

Sub Meters

1.1. Physical Description

FRONT

: The front panel has 3 rows of 4 digits / characters each, with auto scaling “K” kilo, “M”

Mega and “-” negative indications. The “kilo” and “Mega” indications lit together show Giga

readings. Load bar graph on right side of the display gives the indication of consumption in terms

of the %Average load. Five smart-keys make navigating the parameter set very quick and

intuitive for viewing data and configuring (Setup) the EPM 2000.

REAR

: The voltage and current terminals and the communication port are located on the back of

the meter.

1.2. Front Panel

The front panel contains the following indicators and controls:

•

Three rows of Numeric displays, 4 digits each that display three RMS parameters

simultaneously, or one Energy Parameter. The displayed readings update every second.

•

For each row: Kilo, Mega (Kilo + Mega = Giga) indicator and a Negative(-) indicator.

•

Load bar graph gives the indication of consumption in terms of the %Aavg of load.

•

Five keys to scroll through the display pages.

The EPM 2000 products solves the problem of cluttered indicators by prominently displaying the

parameter name right on the large, numeric readouts. For the first time in a Panel Meter, the

Parameter Name is as clearly readable as the value. The name is displayed every 9

second for

2seconds(8+2), as well as each time you press a key. This also allows programmable Phase

Labels in the EPM 2000 products. You can choose from 123 (Factory setting), Abc, ryb, pqr, or

rst.

At this point you can scroll to the next page you want to see. If you’re not sure which page

you’re watching, one press of any key will immediately identify the Name of the Parameter

being displayed. The second key press takes you to the next page.

Figure 1-2: The EPM 2000 front panel with display and keypad

Содержание Multilin EPM 2000 Series





















































Результаты поиска

Содержание Multilin EPM 2000 Series

Отзывы:

Похожие инструкции для Multilin EPM 2000 Series

Бренды по названию

Популярные бренды

GE Multilin EPM 2000 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Multilin EPM 2000 Series

Отзывы:

Похожие инструкции для Multilin EPM 2000 Series

Бренды по названию

Популярные бренды