GE Multilin EPM 2000 Series Скачать руководство пользователя

Страница: 51 / 52

GE Multilin

Sub Meters

3962 VARh_L (Fwd)

Forward Reactive Inductive

Energy

32-bit Float

3964 VARh_C (Fwd)

Forward Reactive Capacitive

Energy

32-bit Float

3966 VAh (Rev)

Reverse Apparent Energy

32-bit Float

3968 Wh (Rev)

Reverse Active Energy

32-bit Float

3970 VARh_L (Rev)

Reverse Reactive Inductive

Energy

32-bit Float

3972 VARh_C (Rev)

Reverse Reactive Capacitive

Energy

32-bit Float

3974 Present Demand

Present Demand

32-bits Float

3976 Rising Demand

Rising Demand

32-bits Float

3978 Max Demand

Maximum Demand

32-bit Float

3980 RESERVED 44

Reserved for Future use

32-bits Float

3982 RESERVED 45

Reserved for Future use

32-bits Float

3984 RESERVED 46

Reserved for Future use

32-bits Float

3986 RESERVED 47

Reserved for Future use

32-bits Float

3988 RESERVED 48

Reserved for Future use

32-bits Float

3990 RESERVED 49

Reserved for Future use

32-bits Float

3992 Max Demand

Time

Maximum Demand occurrence

time

32-bit Long

3994 RUN_SECS

(Fwd)

Forward Seconds Meter Load was

connected since last Reset

32-bit Unsigned Long

3996 RUN_SECS

(Rev)

Reverse Seconds

32-bit Unsigned Long

3998 INTR

Number of Power Outages

32-bit Unsigned Long

6.5.9.

•

Favorites : These

•

Advisable to configure all the

•

The Power Outages (Intr) parameter in Total RMS Block, RMS Phase A Block, RMS

Phase B Block and RMS Phase C Block gives power outages at the meter Auxiliary

(Control Power) Supply and not for individual phases. Therefore all the values will

always be same. If the meter is powered off of a UPS, then these values will remain Zero,

even if the Voltage signals were interrupted.

•

All the RESERVED parameters will return a Zero value. All RESERVED parameters

must therefore be ignored..

•

RunSecs Parameter in Integration block is a high resolution representation of the Run

Hours available on the Meter Front Panel Display. Divide RunSecs by 3600 to get Run

Hours.

•

No scaling or multiplication factor required. All values are already pre-scaled with the PT

and CT scaling programmed into the meter.

Содержание Multilin EPM 2000 Series





















































Результаты поиска

Содержание Multilin EPM 2000 Series

Отзывы:

Похожие инструкции для Multilin EPM 2000 Series

Бренды по названию

Популярные бренды

GE Multilin EPM 2000 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Multilin EPM 2000 Series

Отзывы:

Похожие инструкции для Multilin EPM 2000 Series

Бренды по названию

Популярные бренды