manualshive.com logo in svg

GARDTEC 872, Руководство по установке

Поделиться
Скачать
GARDTEC 872 Скачать руководство пользователя страница 88

9)

Press Yes. The Zone Type you have chosen
will be accepted and the chevron will move
along to the last character on the top line:-

10)

We are now programming what Area(s) the
Zone will be allocated to. By default all zones are
allocated to Area 1.

At this point the number keys 1 to 7 have a toggle
action, pressing number 2 now will add Zone 1
to Area 2 as well as Area 1, pressing 2 again will
remove the zone from Area 2.

Note: A zone may be allocated to a single Area
or multiple Areas.

When the Areas you require are displayed Press
Yes. The display will show for example:-

Don’t forget to program user codes for all the 
Areas you have used.

11)

The chevron has now moved to the attribute for
Zone 1. The attributes available are given on
pages 54 & 55 within this manual. Press No
until the attribute you require is displayed. Then
Press Yes. The display will show for example:-

12)

This is now Zone 2 programming. To continue
programming this (and other) zone(s) repeat
from step 7

To exit from Zone programming press 0 until
the display shows:-

Page 

87

< < < < UN-SET > > > >
01 Jan 00: 00: 01

002 = Access             A =
1                   = Remove -

001 = Ent/Ex              A >
1                   = Remove -

001 = Ent/Ex              A >
13 7              > Remove -

GardTec 

872

Miscellaneous

872.qxd  05/11/2003  15:01  Page 87

Содержание 872

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды