manualshive.com logo in svg

GARDTEC 872, Руководство по установке

Поделиться
Скачать
GARDTEC 872 Скачать руководство пользователя страница 5

2 S

YSTEM

O

VERVIEW

Codes

The GardTec 

872  

is capable of accepting up to 99 user codes plus 1 engineer code.

Each of the user codes is allocated a code type (with the exception of user 1 that is
always Master) at the time the code is programmed. 19 code types plus engineer are
available, these are:-

Code Type 

Code Type 

Master (Default 5678)

Main 7

Cleaner

Area 4

Area 2

Area 5

Area 3

Area 6

Main 1

Area 7

Main 2

Control

Main 3

Set Only

Main 4

Main User

Main 5

Area 1

Main 6

Engineer (Default 1234)

Note 1: 

User 1 will always be Master.

A full list of options that are available for the code types are given in the user manual.
As a general guide for this section the codes for the GardTec 

872 

are split into two

groups, Global and Area codes. Codes allocated to these groups are as follows:-

Global Codes (Controlling All Areas).

Master
Main
Set Only
Engineer 

If any area is set, entering a global code (not Set Only or Cleaner) will unset all areas

If all areas are unset, entering a global code followed by YES (or code then NO YES if
Engineer code is used) will give the option to set all areas.

The global codes with the exception of Set Only also have other options. More details
of these options are given in the user manual.

Page 

4

872.qxd  05/11/2003  15:01  Page 4

Содержание 872

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды