GARDTEC 872 Скачать руководство пользователя страница 25

Страница: 25 / 112

ZONE KEYSWITCH OPTION

Up to eight zones may be allocated as zone keyswitches. This option is carried out via

the ‘Program Zone Type’ option. Either Normal or Biased keyswitches may be used

and the correct option for the keyswitch you are using should be chosen during

programming. Will act on area only refer to Keyswitch Terminal for Global Setting.

Wiring for the keyswitch should be across the AZ pair of the zone, the TZ pair of the

zone may be used in the normal manner.

In order for this keyswitch option to operate there must be an Area User code allocated

for the area that the keyswitch is intended to control, e.g if allocated to control area 2

then an area 2 code needs to be programmed on to the system. Will only work on

single areas.

In order that the keyswitch operations are recorded to the log in the correct manner we

would suggest that the highest user codes (e.g 97 - 99 for 3 keyswitches) are used.

The following example shows a typical format for the user names.

User Name (example)

User Name(example)

Area

User No.

DOOR KEY

MARY KEY

Area 1 User 97

STORES KEY

FRED KEY

Area 2 User 98

SALES

HARRY KEY

Area 3 User 99

Because the GardTec

872

reads the list of users from high to low the log will show for

example Set MARY KEY A1 hh/mm/dd/mm. If User numbers are not reserved or

allocated then the system will use the first code available (reading high to low) for that

particular area set.

Space has been made at the start of the User manual to give indication to an end

user of what user codes, if any have been reserved for this purpose. Please take

time to fill in this section for end user reference.

0V (DIGI)

0V (-VE) connection to a Digital communicator or Red-Care STU

12V (DIGI)

12V (+VE) connection to a Digital communicator or RED-Care STU. The output from

this terminal is protected by the GARD fuse (400mA)*

on the main PCB.

LINE FAULT

This is the Line Fault input terminal. The terminal should be held @12V by the

communicator and swing to 0V to produce a Line Fault condition on the control panel.

If Line Fault is not used the factory fitted resistor to 12V should be left in place.

Note:

To activate this terminal the programmable option 'DIGICOM TYPE' must

be programmed to 'NORMAL'.

Note:

If the GardTec ProDigi or Modem is to be used on serial comms

(plugged into the main PCB) the factory fitted link from this terminal to

12V MUST be removed.

Note:

When DigiModem is used the L/F & 12Hr Terminals cannot be used as

inputs/outputs.

Page

Wiring Connections

GardTec

872

872.qxd 05/11/2003 15:01 Page 24

Содержание 872

















































































































Результаты поиска

Содержание 872

Отзывы:

Бренды по названию

Популярные бренды

GARDTEC 872, Руководство по установке

Результаты поиска

Содержание 872

Отзывы:

Бренды по названию

Популярные бренды