manualshive.com logo in svg

GARDTEC 872, Руководство по установке

Поделиться
Скачать
GARDTEC 872 Скачать руководство пользователя страница 4

1 I

NTRODUCTION

The GardTec 

872 

control panel consists of two main parts, The master control panel

and the keypad(s). The master control panel is a blank end station if the metal version
is used or, the keypad may be mounted on board if the polycarbonate version is used
with standard type keypads. Various zone wiring modes may be used taking the
maximum number of zones available on any one system to 144 zones with 7 areas
with up to 99 user codes.

If required a Radio expansion cards may be fitted and up to two 8 channel receivers.
These Radio expansion cards are compatible with a range of radio equipment.

If required up to two ID expander cards may be fitted instead of standard and radio
expander card. Each ID expander cards will give up to 30 ID zones using industry
standard ID buscuits or ID detectors. When using any expander cards the control
panel zones are retained and are programmable as 8 (4 wire zones) or 16 (2 wire or 2
wire End of Line) zones

Ample room is provided within the master control panel housing for all the system
wiring, Mains connections, Digicom, Modem or Red-Care communicator (fitting inside
the metal version only) and a 7Ah SLA battery.

Uploading/Downloading capabilities are possible on all models within the range
through the GardTec Modem and the GardTec Remote Software Package for a P.C.
Facility is also provided for direct connection to a P.C via the GardTec Modem Patch
Lead.

The capabilities of the GardTec 

872 control panel 

are endless and we strongly

recommend that all the manuals (both engineer and user) are read and understood
before any installation of the system is carried out. You will find that a little time spent
now understanding the GardTec 

872 

will prove to be a great time saver for the future.

It must be stressed that the GardTec 

872  

is one system that is capable of being

split into seven areas. Under no circumstances should you regard it as seven
separate systems.

Page 

3

872.qxd  05/11/2003  15:01  Page 3

Содержание 872

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды