manualshive.com logo in svg

GARDTEC 872, Руководство по установке

Поделиться
Скачать
GARDTEC 872 Скачать руководство пользователя страница 50

Page 

49

Printer Connection

The GardTec 

872 

has an RS232 port that may be connected to a standard serial

printer, to facilitate this two printer leads are available from GardTec Ltd.

Printer Cable No. 1 

Part No 01-091

Connects from PCB direct to printer

Printer Cable No. 2A 

Part No 01-092

Connects from PCB to chassis mounting

DIN socket (to be mounted on panel 

case).

Printer Cable No. 2B

Part No 01-093

DIN plug to printer

The printer should be capable of being set to the following:-

Baud Rate

1200

Data Bits 

8

Parity

None

Stop Bits

4

Carriage Return

None

Note: 

The printer should have its own power supply. Under no circumstances 

should the power for the printer be drawn from the control panel.

The printer may be used in one of three modes:-

1)

For printing the Event Log (user or engineer function). Pressing 1 whilst 

viewing the Event Log will start the printer (refer to user manual for more 

details).

2)

For printing the Program Review (engineer function). Pressing 1 whilst in the 

engineer option Program Review will start the printer.

3)

For Real Time Printing. When Real Time Printing is programmed to ON each 

event that is written to the log will also be sent to the printer. 

This option needs to be set ON from within the engineer programming mode 

(option 96) and may be overridden by the user by using the online / offline 

function on the printer.

Two suggested Printers are currently available, one from RS Components and one

from Farnell Electronics. 

Descriptions and Part Number correct at time of going to

press.

GardTec 

872

Wiring Connections

RS Components

Description

Part No.

24 col/2.5 lps printer

244-632

Power Adaptor

244-654

2 Rolls + 1 Ribbon

202-981

Farnell Electronics

Description

Part No.

Serial Printer 2.5 lps

255-701

Battery Charger UK

231-540

Paper Roll 15m

177-306

Paper Roll 30m

231-952

Ribbon

308-213

872.qxd  05/11/2003  15:01  Page 49

Содержание 872

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды