GARDTEC 872 Скачать руководство пользователя страница 36

Страница: 36 / 112

Page

Fig. 24 Typical 2 Wire Configuration

+ -

12V

+ -

AZ1

+ -

TZ1

+ -

AZ2

+ -

TZ2

+ -

AZ3

+ -

TZ3

+ -

AZ4

+ -

TZ4

+ -

AZ5

+ -

TZ5

+ -

AZ6

+ -

TZ6

+ -

AZ7

+ -

TZ7

+ -

AZ8

+ -

TZ8

ALARM

ZONE 1

+ LOOP

ALARM

ZONE 9

- LOOP

ALARM

ZONE 2

+ LOOP

ALARM

ZONE 10

- LOOP

ALARM

ZONE 3

+ LOOP

ALARM

ZONE 11

- LOOP

ALARM

ZONE 4

+ LOOP

ALARM

ZONE 12

- LOOP

ALARM

ZONE 5

+ LOOP

ALARM

ZONE 13

- LOOP

ALARM

ZONE 6

+ LOOP

ALARM

ZONE 14

- LOOP

ALARM

ZONE 7

+ LOOP

ALARM

ZONE 15

- LOOP

ALARM

ZONE 8

+ LOOP

ALARM

ZONE 16

- LOOP

DETECTOR

SUPPLY

Single Passive Infra-Red
(Use TZ8 zone for tamper)

Normally Closed Alarm Pair

+ Supply

- Supply

Single Contact
(Use AZ8 for tamper)

Exit Terminator Button

(if required)

Normally Open Push Button

Normally Open Pressure Pad

(To Detector Supply -ve)

Single Pressure Pad

(Pressure Pads on AZ Zones
use TZ8 for tamper)

To detector -ve supply

Note:

If exit terminator is required program zone as ET

If unset doorbell is required allocate chime to the

ET zone.

Exit terminator zone must be AZ zone

Setting Mode should be programmed for ET

Note:

AZ zones are +ve
TZ zones are -ve
To comply with BS4737 alarm and tamper loops
should be oposite polarity

Any unused zones may be programmed to off

and the factory fitted link can be removed from the

zone terminals.

It is not advisable to connect normally open devices
onto a TZ loop

Normally Closed Tamper Contacts
for all TZ zones (9-15)

Normally Close Tamper Contacts
for all AZ zones (1-7)

GardTec

872

Wiring Connections

872.qxd 05/11/2003 15:01 Page 35

Содержание 872

















































































































Результаты поиска

Содержание 872

Отзывы:

Бренды по названию

Популярные бренды

GARDTEC 872, Руководство по установке

Результаты поиска

Содержание 872

Отзывы:

Бренды по названию

Популярные бренды