manualshive.com logo in svg

GARDTEC 872, Руководство по установке

Поделиться
Скачать
GARDTEC 872 Скачать руководство пользователя страница 35

Page 

34

Zone Connections 
(control panel 2 Wire option)

The second wiring method is Two Wire. This option will give sixteen zones available
from the control panel PCB.

To use the 2 wire option the control panel should be programmed for
16 (2 WIRE) in the programming section 'PROGRAM ZONE WIRING' (option
No.50)

When this wiring option is programmed zones AZ1 to AZ8 are zones 1 to 8 inclusive,
all AZ zones are positive loops. Zone numbering for the AZ zone will be as follows:-

Zone 1 on terminals AZ1
Zone 2 on terminals AZ2
Zone 3 on terminals AZ3
Zone 4 on terminals AZ4

All AZ zones are positive loops

Zone 5 on terminals AZ5
Zone 6 on terminals AZ6
Zone 7 on terminals AZ7
Zone 8 on terminals AZ8

Because the 2 wire option has been selected the TZ terminals are also programmable
as zones. The zone numbering for the TZ zones will be as follows:- 

Zone 9 on terminals TZ1
Zone 10 on terminals TZ2
Zone 11 on terminals TZ3
Zone 12 on terminals TZ4

All TZ zones are negative loops

Zone 13 on terminals TZ5
Zone 14 on terminals TZ6
Zone 15 on terminals TZ7
Zone 16 on terminals TZ8

It should be noted that in order to comply with the requirements of BS 4737 zones and
tampers should be of opposite polarity. This means that when using the 2 wire wiring
option one AZ  zone (e.g zone 8, AZ8) should be programmed as 24Hr and used as a
global tamper for all TZ zones, and one TZ zone (e.g zone 16, TZ8) should be
programmed as 24Hr and used as a global tamper for all the AZ zones.

Typical wiring of various detectors is given in Fig.24

GardTec 

872

Wiring Connections

872.qxd  05/11/2003  15:01  Page 34

Содержание 872

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды