GARDTEC 872 Скачать руководство пользователя страница 3

Страница: 3 / 112

Page

IMPORT

ANT!

Input:

/-10% ~50Hz 125mA Max. 35W Max
Nominal Temp Range: 0 - 50°C
GardTec

872

Metal Versions

For Indoor Use Only
GardTec

872

Plastic Versions

For Indoor Use Only

This equipment is intended only for use as a Security Alarm Control Panel. Adequate ventilation

away from heat and humidity must be provided. The unit must be fixed securely to a non-

flammable surface using suitable fixings.

All mains wiring must be to BS7671 (1992) IEEE wiring regulations (or appropriate international

regulatory standards). See Mains Supply Connection section within this manual for more

detailed instructions.

All wiring must be protected from sharp or jagged edges.

All Low voltage (alarm) wiring must be to the appropriate international regulatory standards

and comply to good wiring practice. It should not be possible for the Low Voltage wiring to

touch the Mains wiring.

Replacement fuses should be of the same type and rating conforming to IEC 127.

The maximum current draw from the unit for all output combinations

must not exceed 1Amp.

The unit is intended for use with a suitable re-chargeable lead acid battery permanently

connected to the appropriate terminals.

All documentation and manuals must be thoroughly read by suitably qualified installation

personnel prior to installation.

The unit has no user serviceable parts inside. Internal access should only be by suitably quali-

fied personnel.

GardTec

872

Metal Versions

The unit must be Earthed.

It is the responsibility of the installation engineer to ensure that the

earth connection to the unit lid is good on completion of the installation or after service.

GardTec

872

Plastic Versions

Provision is provided for an earth connection within the mains input connector block, this con-

nection is for protection of the wiring only and is not functional for the unit.

GardTec

872

872.qxd 05/11/2003 15:01 Page 2

Содержание 872

















































































































Результаты поиска

Содержание 872

Отзывы:

Бренды по названию

Популярные бренды

GARDTEC 872, Руководство по установке

Результаты поиска

Содержание 872

Отзывы:

Бренды по названию

Популярные бренды