manualshive.com logo in svg

Gardner Denver ELECTRA-SAVER EAQ99Q, Руководство по эксплуатации и обслуживанию, Страница: 72 / 76

Поделиться
Скачать
Gardner Denver ELECTRA-SAVER EAQ99Q Скачать руководство пользователя страница 72

13-9-666    Page 65

SECTION 9
TROUBLESHOOTING

SYMPTOM

POSSIBLE CAUSE

REMEDY

Compressor fails to start

1.

Wrong lead connections.

1.

Change leads.

2.

Blown fuses in control
box.

2.

Replace fuse.

3.

Motor starter overload
heaters tripped .

3.

Reset and investigate
cause of overload.

4.

Pressure in reservoir.

4.

Inspect blowdown valve.

5.

Read error message on
control panel

5.

Take appropriate action.
See Manual 13-9-653.

6.

Remote Contact is open
(terminals 6 & 9).

6.

Replace switch or jumper.

Compressor starts but
stops after a short time

1.

High discharge
temperature.

1.

See “High Discharge Air
Temperature,” this
section.

2.

High discharge
temperature switch
malfunction.

2.

Replace switch

3.

Blown fuse in starter/
control box.

3.

Replace fuse (investigate
if fuses continue to blow).

4.

Motor starter overload
heaters trip.

4.

Reset and investigate
cause of overload.

Compressor does not
unload (or load)

1.

Improperly adjusted
control.

1.

Refer to Manual 13-9-653
and adjust control.

2.

Air leak in control lines.

2.

Determine source of leak
and correct.

3.

Restricted control line.

3.

Clean control lines.

4.

Blowdown valve
malfunction.

4

Repair, clean or replace
valve.

Compressor cycles from
load to unload
excessively

1.

Insufficient receiver
capacity.

1.

Increase receiver size.

2.

Restriction in service
piping

2.

Inspect and clean service
piping.

3.

Restriction in control
tubing.

3.

Inspect and clean control
tubing.

4.

Plugged aftercooler.

4.

Inspect and clean
aftercooler.

Содержание ELECTRA-SAVER EAQ99Q













































































Отзывы:

Нет отзывов