Gardner Denver ELECTRA-SAVER EAQ99Q Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 76

Gardner Denver ELECTRA-SAVER EAQ99Q Скачать руководство пользователя страница 27

13-9-666 Page 20

WARNING

Failure to properly ground the compressor package could result in controller
malfunction.

7.

Rotation

- Check for correct motor rotation using “JOG MODE.” Compressor drive shaft rotation

must be clockwise standing facing the compressor coupling.

WARNING

Operation with incorrect motor rotation can damage equipment and cause oil
eruption from the compressor inlet. When checking motor rotation, induce
minimum rotation (less than one revolution if possible). Never allow motor to
reach full speed.

WARNING

The compressor unit’s direction of rotation must be checked every time the
compressor is reconnected to the power supply.

8.

System Pressure

- Set the controls to the desired load pressure. DO NOT EXCEED THE

MAXIMUM OPERATING PRESSURE ON THE COMPRESSOR NAMEPLATE. See Controller
Manual 13-9-653.

WARNING

Operation at excessive discharge air pressure can cause personal injury or
damage to equipment. Do not adjust the full discharge air pressure above the
maximum stamped on the unit nameplate.

9.

Operating Mode

- Refer to Section 4 for detailed information on the control system.

10.

Enclosure

- Check for damaged panels or doors. Check all screws and latches for tightness. Be

sure doors are closed and latched.

«
...
25
26
27
28
29
...
»

Содержание ELECTRA-SAVER EAQ99Q













































































Отзывы:

Нет отзывов