Gardner Denver ELECTRA-SAVER EAQ99Q Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 76

Gardner Denver ELECTRA-SAVER EAQ99Q Скачать руководство пользователя страница 16

13-9-666 Page 9

Air-Cooled Units

- A combination oil/aftercooler is supplied as standard equipment on all air-cooled

units. The air-cooled unit with the standard enclosure requires sufficient flow, Figure 2-2, for the
compressor oil/aftercooling system and for electric motor cooling. Air is drawn into the unit at the motor
side of the enclosure and is exhausted at the oil cooler side. Do not block the air flow to and from the
unit. Allow three and one-half (3-1/2) feet (1.1 m) to the nearest obstruction on the starter end and control
box end of the unit. Allow three (3) feet (.9 m) to the nearest obstruction above and on other sides of unit.
For continuous efficiency, oil cooler cores must be periodically cleaned with either vacuum or compressed
air. If wet cleaning is required, shield motor and spray on a mild soap solution and flush with clean water.

Minimum Air Flow * For Compression and Cooling

HP (kW)

Air Cooled

Water Cooled

125, 150, 200

(93, 112, 150)

17,000 cfm

481 m

3

/min

4,000 cfm

113 m

3

/min.

* 80

°

F (27

°

C) Inlet Air

Figure 2-2 – AIR FLOW CHART

WARNING

These compressors have aluminum oil coolers, do not use any cleaning
solution that is not compatible with aluminum. Use of improper solution may
result in damage to the cooler.

Water-Cooled Units

- The water-cooled unit with the standard enclosure requires sufficient air flow,

Figure 2-2, for electric motor cooling. Air is drawn into the unit at the top of the enclosure and is
exhausted at the motor side. Do not block air flow to and from unit. Allow three and one-half (3-1/2) feet
(1.1 m) to the nearest obstruction on the starter end and control box side of the unit. Allow three (3) feet
(.9 m) to the nearest obstruction above and on other sides of the unit.

FOUNDATION

- The Gardner Denver Rotary Screw compressor requires no special foundation, but

should be mounted on a smooth, solid surface. Whenever possible install the unit near level. Temporary
installation may be made at a maximum 10

°

angle lengthwise or 10

°

sidewise.

Mounting bolts are not normally required. However, installation conditions such as piping rigidity, angle of
tilt, or danger of shifting from outside vibration or moving vehicles may require the use of mounting bolts
and shims to provide uniform support for the base.

«
...
14
15
16
17
18
...
»

Содержание ELECTRA-SAVER EAQ99Q













































































Отзывы:

Нет отзывов