Gardner Denver ELECTRA-SAVER EAQ99Q Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 76

Gardner Denver ELECTRA-SAVER EAQ99Q Скачать руководство пользователя страница 17

13-9-666 Page 10

OIL RESERVOIR DRAIN

- The oil drain is piped from the bottom of the reservoir to the side of the frame.

This drain is approximately 4.50 inches (115 mm) above the floor level. If this is not sufficient to
conveniently drain the oil some other methods of providing drain are:

1.

Elevate the compressor unit on a suitable structure to obtain the desired drain height.

2.

Construct an oil sump or trough below the floor level and pump or bail the drained oil.

3.

Pump oil from the reservoir filler opening or drain to a container.

CAUTION

If the compressor unit base is raised above floor level, the space between the
floor and the base bottom must be closed with solid material all around to
prevent recirculation of hot air from the oil cooler end and over temperature
operation.

ENCLOSURE

- The compressor, electric motor, oil cooler and aftercooler are mounted inside the

enclosure. Service doors are provided for maintenance access. Be sure to allow enough space around
the unit for the doors to open completely. Any of the enclosure doors may be removed by opening the
door and lifting it up slightly to disengage the hinges.

The motor inspection/air filter service panel is held by two latches and lifts away from the enclosure. The
air outlet panel is attached by screws to the enclosure and is not readily removable.

DANGER

Do not operate the compressor with the fan and coupling guard removed.
Exposed fan and couplings may cause injury to personnel.

«
...
15
16
17
18
19
...
»

Содержание ELECTRA-SAVER EAQ99Q













































































Отзывы:

Нет отзывов