Gardner Denver ELECTRA-SAVER EAQ99Q Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 76

Gardner Denver ELECTRA-SAVER EAQ99Q Скачать руководство пользователя страница 59

13-9-666 Page 52

COMPRESSOR OIL COOLER - RADIATOR TYPE

(

Figure 1-5

, page 3) - The oil cooler motor and fan is

mounted on the oil cooler module; air is exhausted through the oil cooler and away from the unit. Do not
obstruct air flow to and from the oil cooler. Allow a minimum of three (3) feet clearance around the cooler.
Keep both faces of cooler core clean for efficient cooling of compressor oil.

Figure 5-9 – THERMOSTATIC MIXING VALVE ELEMENT

THERMAL CONTROL (THERMOSTATIC MIXING) VALVE

(

Figure 5-9

) is installed in system as shown in

Figure 5-3

, page 43. This valve is used to control temperature of the oil in both air-cooled radiator and

water-cooled heat exchanger type oil cooler systems. On start-up with unit cold, element is open to
bypass, allowing oil to pass directly from the reservoir to compressor during warm-up. As oil warms,
element gradually closes to the bypass allowing more of the oil from the cooler to mix with oil from the
bypass.

After the unit is warmed up, the mixing valve maintains oil injection temperature into the compressor at a
minimum of 150

°

F (66

°

C). This system provides proper compressor warm-up and helps prevent

moisture contamination of oil.

To check element, heat in oil - it should be fully extended at 150

°

F (66

°

C). If unit shuts down due to

high air discharge temperature, it may be that one or both thermostatic mixing valve elements (

Figure 5-3

,

page 43) are stuck open. Remove mixing valve and clean all parts thoroughly when flushing the oil
system.

DANGER

Compressor, air/oil reservoir, separation chamber and all piping and tubing
may be at high temperature during and after operation.

COMPRESSOR OIL COOLER - WATER-COOLED HEAT EXCHANGER

(Figure 5-3, page 43) - The

heat exchanger oil cooler is a multiple pass type, with water in the tubes and oil in the shell. The oil
temperature is controlled by the thermal (thermostatic mixing) valve. The optional water control valve
may be used to conserve water.

«
...
57
58
59
60
61
...
»

Содержание ELECTRA-SAVER EAQ99Q













































































Отзывы:

Нет отзывов