Gardner Denver ELECTRA-SAVER EAQ99Q Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 76

Gardner Denver ELECTRA-SAVER EAQ99Q Скачать руководство пользователя страница 58

13-9-666 Page 51

COMPRESSOR OIL FILTER

(

Figure 5-3

, page 43) - This screw on oil filter is a vital part in maintaining a

trouble-free compressor, since it removes dirt and abrasives from the circulated oil. The oil filter relief
valve is integrated into the replaced oil filter element.

CAUTION

Improper oil filter maintenance will cause damage to equipment. Replace filter
element every 1000 hours of operation. More frequent replacement could be
required depending on operating conditions. A filter element left in service too
long may damage equipment.

Use only the complete oil filter for replacement. The part number is on the filter head and in the parts list.

DANGER

Air/oil under pressure will cause severe personal injury or death. Shut down
compressor, relieve system of all pressure, disconnect, lockout and tagout
power supply to the starter before removing valves, caps, plugs, fittings, bolts
and filters.

DANGER

Compressor, air/oil reservoir, separation chamber and all piping and tubing
may be at high temperature during and after operation.

Use the following procedure to replace the filter. Do not disturb the piping:

1.

To remove the oil filter, use a 1” socket to unthread the oil filter from the housing.

2.

Rotate the filter head (aluminum assembly) to align the channel in the head with the tabs on the
oil filter element..

3.

Lift the threaded part of the filter head until it is seated against the top of the filter head.

4.

With the channel aligned and the threaded portion of the filter head against the top of the filter
head, disassemble the filter element from the filter head.

5.

To install a new oil filter, rotate the threaded portion of the filter head to align the channel.

6.

Align the tabs on the filter element with the channels in the filter head and snap the element into
the filter head.

7.

Press the filter assembly into the filterstat assembly. Using a 1” socket tighten down the oil
filter, until the o-ring seals. Do not overtighten.

8.

Run the unit and check for leaks.

«
...
56
57
58
59
60
...
»

Содержание ELECTRA-SAVER EAQ99Q













































































Отзывы:

Нет отзывов