Gardner Denver ELECTRA-SAVER EAQ99Q Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 76

Gardner Denver ELECTRA-SAVER EAQ99Q Скачать руководство пользователя страница 15

13-9-666 Page 8

SECTION 2
INSTALLATION

GENERAL

- On receipt of the unit, check for any damage that may have been incurred during transit.

Report any damage or missing parts as soon as possible.

CAUTION

Do not electric weld on the compressor or base; bearings can be damaged by
passage of current.

LIFTING UNIT

- Proper lifting and/or transporting methods must be used to prevent damage. Lifting slots

are provided in the base for towmotor use. The unit may also be moved into location by rolling on bar.

CAUTION

Lift compressor unit by base only. Do not use other places such as motor,
compressor or discharge manifold piping as lifting points.

DANGER

The eyebolts or lugs provided on the motor are for lifting the motor only and
should not be used to lift any additional weight. All eyebolts must be securely
tightened. When lifting the motor, the lifting angle must not exceed 15 degrees.
Failure to observe this warning may result in damage to equipment or personal
injury.

LOCATION

- The compressor should be installed, whenever possible, in a clean, well-lighted, well-

ventilated area with ample space all around for maintenance. Select a location that provides a cool,
clean, dry source of air. In some cases it may be necessary to install the air filter at some distance from
the compressor to obtain proper air supply.

Both the air-cooled and water-cooled units require cooling air as well as air to the compressor inlet.
Proper ventilation MUST be provided; hot air must be exhausted from the compressor operating area. A
typical inlet-outlet air flow arrangement is shown in Figure 2-1.

Figure 2-1 – TYPICAL COMPRESSOR ROOM

«
...
13
14
15
16
17
...
»

Содержание ELECTRA-SAVER EAQ99Q













































































Отзывы:

Нет отзывов