FujiFilm FRENIC5000G11S Series, Техническая информация

Страница: 13 / 236

1-7
Chapter 1
2. Common Specifications
1
NOTE : ( ) or < > in the “Remarks” column indicates the abbreviation of terminal function assigned to digital input terminals X1 to X9 and
transistor (relay) output terminals Y1 to Y4 (Y5A, Y5C).
Control Bias frequency F18
Gain for frequency F17
setting
Jump frequency control C01 to C04
Rotating motor pick up
H09
(Flying start)
Auto-restart after
F14
momentary power failure
H13 to H16
Line/Inverter E01 to E09
changeover operation E20 to E24, H13
Slip compensation P09
A18
Droop operation H28
Torque limiting F40, F41
E16, E17
Torque control H18
PID control H20 to H25
F01
C05 to C19
H21
Automatic deceleration
F41, E17
Second motor's setting
A01 to A18
Energy saving operation
H10
Fan stop operation H06
Universal DI
Universal DO
Bias frequency can be preset.
Gain for frequency setting can be preset. (0.0 to 200.0%)
ex.) Analog input 0 to +5Vdc with 200% gain results in
Maximum frequency at 5Vdc.
Jump frequency (3 points) and its common jump hysteresis width
(0 to 30Hz) can be preset.
A rotating motor(including inverse rotating mode) can be smoothly
picked up without stopping the motor. (speed search method)
Automatic restart is available without stopping motor after a
momentary power failure. (speed search method)
When "Smooth recovery" mode is selected, the motor speed drop
is held minimum.
Controls switching operation between line power and inverter.
The inverter has sequence function inside.
• The inverter output frequency is controlled according to the load
torque to keep motor speed constant.
•
When the value is set at "0.00" and "Torque-vector" is set at "active", the
compensation value automatically selects the Fuji standard motor.
Slip compensation can be preset for the second motor.
The motor speed droops in proportional to output torque.(-9.9 to
0.0Hz) ...G11S only
When the motor torque reaches a preset limiting level, this function
automatically adjusts the output frequency to prevent the inverter
from tripping due to an overcurrent.
Torque limiting 1 and Torque limiting 2 can be individually set, and
are selectable with a digital input signal.
Output torque (or load factor ) can be controlled with an analog
input signal (terminal 12).
This function can control flowrate, pressure, etc. (with an analog feedback signal.)
•••••
Reference signal
• KEYPAD operation (
∨
or
∨
key) :
Setting freq. / Maximum freq. X 100 [%]
• Voltage input (terminal 12 and V2) :
0 to 10Vdc / 0 to 100%
• Current input (terminal C1) :
4 to 20mAdc / 0 to 100%
• Reversible operation with polarity (terminal 12) :
0 to
±
10Vdc / 0 to
±
100%
• Reversible operation with polarity (terminal 12 + V1) :
0 to
±
10Vdc / 0 to
±
100%
• Inverse mode operation (terminal 12 and V2) :
10 to 0Vdc / 0 to 100%
• Inverse mode operation (terminal C1) :
20 to 4mAdc / 0 to 100%
• PATTERN operation :
Setting freq. / Maximum freq. X 100 [%]
• DI option input :
• BCD...
Setting freq. / Maximum freq. X 100 [%]
• Binary...Full scale / 100%
• Multistep frequency setting :
Setting freq. / Maximum freq. X 100 [%]
• RS-485 :
Setting freq. / Maximum freq. X 100 [%]
•••••
Feedback signal
•
Terminal 12 (0 to 10Vdc / 0 to 100%, or 10 to 0Vdc / 0 to 100% )
•
Terminal C1 (4 to 20mAdc / 0 to 100%, or 20 to 4mAdc / 0 to 100%)
Torque limiter 1 (Braking) is set at "F41: 0".
(Setting of Torque limiter 2 (Braking) is same.)
• In deceleration :
The deceleration time is automatically extended up to 3 times for
tripless operation even if a braking resistor is not used.
• In constant speed operation :
Based on regenerative energy, the frequency is increased, and
tripless operation is active.
This function is used for two motors switching operation.
•
The second motor's V/f characteristics (base and maximum frequency),
rated current, torque boost, electronic thermal relay, etc. can be preset.
• The second motor's circuit parameter can be preset, and torque-
vector control can be applied to both motors.
This function minimizes inverter and motor losses at light load.
• This function detects temperature inside inverter to stop cooling
fans for silent operation and extending the fans' lifetime.
• On/off status of cooling fans is output.
Transmits to main controller of LINK operation
Outputs command signal from main controller of LINK operation.
Item Explanation Remarks Func. code
When the sum of setting frequency and bias
frequency is minus value, the output
frequency rise can be delayed. (No reverse
running is performed.)
(STM)
The inverter searches the motor speed, and
smoothly returns to setting frequency.
Even if the motor circuit is temporarily opened,
the inverter operates without a hitch.
(SW50, SW60)
<SW88, SW52-1, SW52-2>
Slip compensation value can be manually
set from 0.01 to 5.00Hz instead of 0.0 for
FUJI standard motor.
P11S series doesn't have this function.
(TL2/TL1)
• Torque polarity selectable. (Hz/TRQ)
• P11S series doesn't have this function.
•
PID control is selected by "H20". (Hz/PID).
•
Reference signal selection is made by "F01"
.
In "F01", "8: UP/DOWN control 1", "9: UP/
DOWN control 2", and "11: Pulse train
input" cannot be used for the reference
signal of PID control.
• Terminal V1 is optional.
• Terminal V2: EN only
•
Feedback signal selection is made by "H21".
When the deceleration time is extended to
longer than three times the setting time, the
inverter trips.
(M2/M1)
<SWM2>
<FAN>
(U-DI)
<U-DO>
Chapter01J(P6˜18).p65
07.8.10, 10:37 Page 7
Adobe PageMaker 6.5J/PPC