FujiFilm FRENIC5000G11S Series, Техническая информация

Страница: 112 / 236

2-64
Chapter 2
4. Standard RS-485 Interface
4.6 Function data format
The data formats for various function data of the inverters are defined here. The data shall be prepared according to the following
data format specifications. The instruction manual of inverter shall be referred to for the range and unit of data.
4.6.1 List of function data format
NOTE:
*1) 0.75 kHz is treated as 0000H.
Code Name Data format Code Name Data format
F00 Data protection [1]
F01 Frequency command 1 [1]
F02 Operation method [1]
F03 Maximum output frequency 1 [1]
F04 Base frequency 1 [1]
F05 Rated voltage 1 [1]
F06 Maximum output voltage 1 [1]
F07 Acceleration time 1 [12]
F08 Deceleration time 1 [12]
F09 Torque boost 1 [3]
F10 Electronic thermal overload relay 1 (Selection) [1]
F11 Electronic thermal overload relay 1 (Level) [12]
F12 Electronic thermal overload relay 1 [3]
(Thermal time constant )
F13 Electronic thermal overload relay (Braking resistor) [1]
F14 Restart after momentary power failure (Selection) [1]
F15 Frequency limiter (High) [1]
F16 Frequency limiter (Low) [1]
F17 Gain (for frequency setting signal) [3]
F18 Bias frequency [4]
F20 DC brake (Starting frequency) [3]
F21 DC brake (Braking level) [1]
F22 DC brake (Braking time) [3]
F23 Starting frequency [3]
F24 Starting frequency (Holding time) [3]
F25 Stop frequency [3]
F26 Motor sound (Carrier frequency) [1] *1
F27 Motor sound (Sound tone) [1]
F30 FMA terminal (Voltage adjust) [1]
F31 FMA terminal (Function selection) [1]
F33 FMP terminal (Pulse rate multiplier) [1]
F34 FMP terminal (Voltage adjust) [1]
F35 FMP terminal (Function selection) [1]
F36 30Ry operation mode [1]
F40 Torque limit 1 (Driving) [1]
F41 Torque limit 1 (Braking) [1]
F42 Torque vector control 1 [1]
E01 X1 terminal function [1]
E02 X2 terminal function [1]
E03 X3 terminal function [1]
E04 X4 terminal function [1]
E05 X5 terminal function [1]
E06 X6 terminal function [1]
E07 X7 terminal function [1]
E08 X8 terminal function [1]
E09 X9 terminal function [1]
E10 Acceleration time 2 [12]
E11 Deceleration time 2 [12]
E12 Acceleration time 3 [12]
E13 Deceleration time 3 [12]
E14 Acceleration time 4 [12]
E15 Deceleration time 4 [12]
E16 Torque limiter 2 (Driving) [1]
E17 Torque limiter 2 (Braking) [1]
E20 Y1 terminal function [1]
E21 Y2 terminal function [1]
E22 Y3 terminal function [1]
E23 Y4 terminal function [1]
E24 Y5A, Y5C terminal functions [1]
E25 Y5 logical reverse functiom [1]
E30 Frequency arrival (FAR) (Detecting width) [3]
E31 Frequency detection 1 (FDT) (level) [1]
E32 Frequency detection (FDT) (Hysteresis width) [3]
E33 Overload early warning (Mode selection) [1]
E34 Overload early warning 1 (level) [12]
E35 Overload early warning (Timer time) [3]
E36 Frequency detection 2 (FDT) (level) [1]
E37 Overload early warning 2 (level) [12]
E40 Display coefficient A [12]
E41 Display coefficient B [12]
E42 Display filter [3]
E43 LED monitor (Display selection) [1]
E44 LED monitor (Display at STP mode) [1]
E45 LCD monitor (Display selection) [1]
E46 LCD monitor (Language) [1]
E47 LCD monitor (Contrast adjustment) [1]
Chapter02J(P44˜74).p65
07.8.9, 12:26 Page 64
Adobe PageMaker 6.5J/PPC