FujiFilm FRENIC5000G11S Series, Техническая информация

Страница: 113 / 236

2-65
Chapter 2
4. Standard RS-485 Interface
2
NOTE:
*1) 999 is treated as 03E7H (99.9).
*2) Read-only from communication.
*3) The communication might not be able to be continued by writing (data 1).
Code Name Data format Code Name Data format
C01 Jump frequency 1 [1]
C02 Jump frequency 2 [1]
C03 Jump frequency 3 [1]
C04 Jump frequency (Width) [1]
C05 Multi-step frequency 1 [5]
C06 Multi-step frequency 2 [5]
C07 Multi-step frequency 3 [5]
C08 Multi-step frequency 4 [5]
C09 Multi-step frequency 5 [5]
C10 Multi-step frequency 6 [5]
C11 Multi-step frequency 7 [5]
C12 Multi-step frequency 8 [5]
C13 Multi-step frequency 9 [5]
C14 Multi-step frequency 10 [5]
C15 Multi-step frequency 11 [5]
C16 Multi-step frequency 12 [5]
C17 Multi-step frequency 13 [5]
C18 Multi-step frequency 14 [5]
C19 Multi-step frequency 15 [5]
C20 Jogging frequency [5]
C21 Pattern operation [1]
C22 Stage 1 [13]
C23 Stage 2 [13]
C24 Stage 3 [13]
C25 Stage 4 [13]
C26 Stage 5 [13]
C27 Stage 6 [13]
C28 Stage 7 [13]
C30 Frequency setting [1]
C31 Analog input offset (terminal 12) / [4]
Analog input bias (terminal 12)
C32 Analog input offset (terminal C1) / [4]
Analog input gain (terminal 12)
C33 Analog filter [5]
P01 Motor 1 (Number of poles) [9]
P02 Motor 1 (Capacity) [5]
P03 Motor 1 (Rated current) [12]
P04 Motor 1 (Auto-tuning) [1]
P05 Motor 1 (On-line tuning) [1]
P06 Motor 1 (No-load current) [12]
P07 Motor 1 (%R1) [5]
P08 Motor 1 (%X) [5]
P09 Motor 1 (Slip compensation control ) [5]
H03 Data initializing [1] *3
H04 Auto-reset (Times) [1]
H05 Auto-reset(Reset interval) [1]
H06 Fan stop operation [1]
H07 ACC/DEC pattern (Mode selection) [1]
H08 Reverse phase sequence lock [1]
H09 Start mode (Pick-up mode) [1]
H10 Energy-saving operation [1]
H11 Deceleration mode [1]
H12 Instantaneous overcurrent limiting [1]
H13 Auto-restart (Restart time) [3]
H14 Auto-restart (Frequency fall rate) [5]
H15 Auto-restart (Holding DC voltage) [1]
H16 Auto-restart (OPR command selfhold time) [3] *1
H18 Torque control (Mode selection) [1]
H19 Active drive [1]
H20 PID control (Mode selection) [1]
H21 PID control (Feedback signal) [1]
H22 PID control (P-Gain) [5]
H23 PID control (I-time) [3]
H24 PID control (D-time) [5]
H25 PID control (Feedback filter) [3]
H26 PTC thermistor (Mode selection) [1]
H27 PTC thermistor (Level) [5]
H28 Droop operation [4]
H30 Serial link (Function selection) [1]
H31 RS-485 (Address) [1] *2
H32 RS-485 (Mode selection on error) [1] *2
H33 RS-485 (Timer time) [3] *2
H34 RS-485 (Baud rate) [1] *2
H35 RS-485 (Data length) [1] *2
H36 RS-485 (Parity check) [1] *2
H37 RS-485 (Stop bits) [1] *2
H38 RS-485 (No response detection time) [1] *2
H39 RS-485 (Response interval) [5] *2
A01 Maximum frequency 2 [1]
A02 Base frequency 2 [1]
A03 Rated voltage 2 (at base speed) [1]
A04 Maximum output voltage 2 [1]
A05 Torque boost 2 [3]
A06 Electronic thermal 2 (Selection) [1]
A07 Electronic thermal 2 (Level) [12]
A08 Electronic thermal 2 (Thermal time constant) [3]
A09 Torque vector control 2 [1]
A10 Motor 2 (Number of motor-2 poles) [9]
A11 Motor 2 (Capacity) [5]
A12 Motor 2 (Rated current) [12]
A13 Motor 2 (Auto-tuning) [1]
A14 Motor 2 (On-line tuning) [1]
A15 Motor 2 (No-load current [12]
A16 Motor 2 (%R1 setting) [5]
A17 Motor 2 (%X setting) [5]
A18 Motor 2 (Slip compensation control 2) [5]
Chapter02J(P44˜74).p65
07.8.9, 12:26 Page 65
Adobe PageMaker 6.5J/PPC