Fronius Primo GEN24 3.0 Plus Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 160

Fronius Primo GEN24 3.0 Plus Скачать руководство пользователя страница 95

IMPORTANT!

When configuring "PV Point" backup power mode, the information in chapter

on

page

must be observed.

When configuring "Full Backup" backup power mode, the information in chapter

on page

must be observed.

Backup power nominal voltage

When backup power mode is activated, the nominal voltage of the public grid must be
selected.

State of charge warning limit

A warning is output when the residual capacity of the battery specified here is reached in
backup power mode.

Reserve capacity

The set value results in a residual capacity (depending on the capacity of the battery)
that is reserved for backup power. The battery is not discharged below the residual capa-
city in grid-connected operation.

Load management

Up to four pins can be selected for load management here. Additional load management
settings are available in the "Load management" menu item.
Default: Pin 1

Australia - Demand Response Mode (DRM)

The pins for control via DRM can be set here:

Mode

Description

Information

DRM pin

I/O pin

DRM0

Inverter disconnects
itself from the grid

DRM0 occurs if there is an
interruption or short circuit
on the REF GEN or COM
LOAD leads, or if the com-
binations DRM1 - DRM8
are invalid.
The mains relays open.

REF GEN

COM

LOAD

IO4
IO5

DRM1

Import P

nom

≤ 0%

without disconnection
from the grid

currently not supported

DRM 1/5

IN6

DRM2

Import P

nom

≤ 50%

currently not supported

DRM 2/6

IN7

DRM3

Import P

nom

≤ 75% &

+Q

rel

* ≥ 0%

currently not supported

DRM 3/7

IN8

DRM4

Import P

nom

≤ 100%

currently not supported

DRM 4/8

IN9

DRM5

Export P

nom

≤ 0%

without disconnection
from the grid

currently not supported

DRM 1/5

IN6

DRM6

Export P

nom

≤ 50%

currently not supported

DRM 2/6

IN7

DRM7

Export P

nom

≤ 75% &

-Q

rel

* ≥ 0%

currently not supported

DRM 3/7

IN8

DRM8

Export P

nom

≤ 100%

currently not supported

DRM 4/8

IN9

The percentages always refer to the nominal device output.

IMPORTANT!

If the Demand Response Mode (DRM) function is enabled and no DRM control is con-
nected, the inverter switches to Standby mode.

95

EN

«
...
93
94
95
96
97
...
»

Содержание Primo GEN24 3.0 Plus

































































































































































Отзывы:

Нет отзывов