manualshive.com logo in svg

Fronius Primo GEN24 3.0 Plus, Руководство по эксплуатации, Страница: 51 / 160

Поделиться
Скачать
Fronius Primo GEN24 3.0 Plus Скачать руководство пользователя страница 51

Install the mounting bracket and hang up the

inverter

Selecting the fix-
ing material

Use the corresponding fixing materials depending on the subsurface and observe the
screw dimension recommendations for the mounting bracket.
The installer is responsible for selecting the right type of fixing.

Properties of the
mounting bracket

The mounting bracket (illustration) can
also be used as a guide.

The pre-drilled holes on the mounting
bracket are intended for screws with a
thread diameter of 6-8 mm (0.24-0.32
inches). The distance from the left to the
right pre-drilled hole is 16 inches.

Unevenness on the mounting surface
(such as coarse-textured plaster) is largely
compensated by the mounting bracket.

Do not deform
the mounting
bracket

NOTE!

When fitting the mounting bracket to the wall or column, ensure that the mounting
bracket does not become deformed.

A deformed mounting bracket may make it difficult to clip/swivel the inverter into position.

Fitting the mount-
ing bracket to a
wall

IMPORTANT!

When installing the mounting bracket, make sure that it is installed with the arrow point-
ing upwards.

1

2

51

EN

Содержание Primo GEN24 3.0 Plus

































































































































































Отзывы:

Нет отзывов