Fronius Primo GEN24 3.0 Plus Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 160

Fronius Primo GEN24 3.0 Plus Скачать руководство пользователя страница 29

Modbus 0 (MB0) switch

Switches the terminating resistor for
Modbus 0 (MB0) on/off.

Position 1:

Terminating resistor on

(factory setting)

Position 0:

Terminating resistor off

Modbus 1 (MB1) switch

Switches the terminating resistor for
Modbus 1 (MB1) on/off.

Position 1:

Terminating resistor on

(factory setting)

Position 0:

Terminating resistor off

Optical sensor

To operate the inverter. See chapter

Button functions and LED status
indicator

on page

Communication LED

Indicates the inverter connection status.

Operating status LED

Indicates the inverter operating status.

LAN 1

Ethernet connection for data communic-
ation (e.g. WLAN router, home network
or for commissioning with a laptop, see
chapter

Installation using the web

on page

LAN 2

Ethernet connection only for data com-
munication from inverter to inverter (cur-
rently unavailable).

WSD terminal

Push-in terminal for the WSD installa-
tion. See chapter

WSD (wired shut-

on page

.

USB

Power supply max. 1 A at 5 V. Software
updates and data recording via USB is
not possible.

IOs terminal

Push-in terminal for digital inputs/
outputs. See chapter

Permitted cables

for the data communication area

page

.

The designations (RG0, CL0, 1/5, 2/6,
3/7, 4/8) on the terminal refer to the
Demand Response Mode function, see
chapter

Functions andI/Os

on page

Internal schem-
atic connection
diagram of the
IOs

On the V+/GND pin, it is possible to feed in a voltage of around 12.5 - 24 V (+ max. 20%)
with an external power supply. The outputs IO 0 - 5 can then be operated with the
external voltage. A maximum of 1 A can be drawn per output, with a maximum of 3 A
allowed in total. The fuse protection must be located externally.

29

EN

«
...
27
28
29
30
31
...
»

Содержание Primo GEN24 3.0 Plus

































































































































































Отзывы:

Нет отзывов