manualshive.com logo in svg

Fronius Primo GEN24 3.0 Plus, Руководство по эксплуатации, Страница: 45 / 160

Поделиться
Скачать
Fronius Primo GEN24 3.0 Plus Скачать руководство пользователя страница 45

General

Quick-lock sys-
tem

A quick-lock system (3) is used to mount
the connection area cover and front cover.
The system is opened and closed with a
half-rotation (180°) of the captive screw (1)
into the quick-lock spring (2).

The system is independent of torque.

NOTE!

Danger when using a drill driver.

This may result in the destruction of the quick-lock system due to overtorque.

▶

Use a screwdriver (TX20).

▶

Do not turn the screws more than 180°.

Warning notices
on the device

Technical data, warning notices and safety symbols are affixed to the inverter. These
warning notices and safety symbols must not be removed or painted over. They warn
against incorrect operation which can lead to serious injury and property damage.

Symbols on the rating plate:

The devices comply with all the requisite and relevant standards and
guidelines that form part of the relevant EU Directive, and are therefore permit-
ted to display the CE mark.

45

EN

Содержание Primo GEN24 3.0 Plus

































































































































































Отзывы:

Нет отзывов