Fronius Primo GEN24 3.0 Plus Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 160

Fronius Primo GEN24 3.0 Plus Скачать руководство пользователя страница 87

inverter feeds energy into the grid at maximum 500 W and the operating status LED
flashes yellow.

The country setup can only be set when using the inverter for the first time. If the country
setup needs to be changed at a later date, please contact your installer / Technical Sup-
port team.

Button functions
and LED status
indicator

The status of the inverter is
shown via the operating status
LED. In the event of faults, carry
out the individual steps in the
Fronius Solar.web live app.

The optical sensor is actuated by
touching with a finger.

The status of the connection is
shown via the communication
LED. To establish the connection,
carry out the individual steps in
the Fronius Solar.web live app.

Sensor functions

1x = WLAN access point (AP) is opened.

Flashing blue

2x = WLAN Protected Setup (WPS) is activated.

Flashing green

3 seconds (max. 6 seconds) = the service notification is ter-
minated and the key lock is deactivated.

Lights up yellow

LED status indicator

The inverter is operating correctly.

Lights up green

The inverter starts.

Flashing green

The inverter is in standby, is not operational (e.g. no feed-in at
night) or is not configured.

Lights up yellow

87

EN

«
...
85
86
87
88
89
...
»

Содержание Primo GEN24 3.0 Plus

































































































































































Отзывы:

Нет отзывов