Fri-Jado Deli Multisserie Скачать руководство пользователя страница 51

Страница: 51 / 132

REMOVAL AND REPLACEMENT OF PARTS

Page 51

Service Manual Deli Multisserie form 9123667 rev. 20220317

1 mm

±8 mm

1. Open the top of the unit.
2. Unscrew 3 screws at the top.
3. Pull a screwdriver in the seam of the

curved frontpanel [567] and push it out.

4. Loosen the set screw [871] a few turns and

pull out the reed switch.

5. Disconnect the reedswitch from the cera-

mic terminal block [69].

Reverse the procedure to mount the switch.
• Adjust the switch as shown on the pic-

ture!

• Do not put too much force on the screw!

The switch is inside the hollow brass pipe.

History.

A. Untill serial number 100047331 (April

2009), the reed switch has been placed at
the hinge side. The switch is placed “paral-
lel” to the magnet.

B. Untill serial number 100051088 the reed

switch has been placed at the handle side,
also “parallel” to the magnet.

C. Untill serial number 100051252, the reed

switch has been placed at the handle side
“in series ” with the magnet with help of
a 90° bush.

D. From 100051253, the reed switch has been

mounted as shown on picture 4 and 6
with a welded bush.

In case of doubt of good functioning, in situ-

ation “B”, it is advised to update to situa-
tion “C” with help of the 90° bush.

Necessary parts (3x)
9192347 - 90° bush
9191049 - Set screw M5x5

EXCHANGING THE DOORSWITCHES

Reed switch at hinge side (untill 100047331)

Mounting position

Parallel to magnet

Reed switch at handle side (from100047332)

Mounting position

Parallel to magnet

Improved with

90° bush!

Содержание Deli Multisserie





































































































































Результаты поиска

Содержание Deli Multisserie

Отзывы:

Похожие инструкции для Deli Multisserie

Бренды по названию

Популярные бренды

Fri-Jado Deli Multisserie, Руководство по обслуживанию

Результаты поиска

Содержание Deli Multisserie

Отзывы:

Похожие инструкции для Deli Multisserie

Бренды по названию

Популярные бренды