Fri-Jado Deli Multisserie Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 132

background image

TROUBLE SHOOTING

Page 77

Service Manual Deli Multisserie form 9123667 rev. 20220317

Error message

Description

Possible causes

......... sensor open

(in general)

The temperature sensor input reads
higher than 320°C (600°F).

In resistance, this is higher than 2200Ω.

..........sensor shorted

(in general)

The temperature sensor input reads lo-
wer than 0°C (32°F).

In resistance, this is lower than 1000Ω.

Top sensor open

Top sensor broken or wiring loose

Btm sensor open

Bottom sensor broken or wiring loose.

Core sensor open

Core sensor broken or wiring loose.

Top sensor shorted

Top sensor broken or wiring shorted

Btm sensor shorted

Bottom sensor broken or wiring shorted

Core sensor shorted

Core sensor broken or wiring shorted.

Powerboard fails
(See next chapter)

Communication problem between the
Power & I/O board and the CPU board

Broken Power & I/O board or connection
problem in ribbon cable (connector).

Slave board fails

(See next chapter)

Communication problem between the
Extension I/O board and the CPU board.
(Multisserie and ACR)

Broken I/O extension board or connection
problem in ribbon cable (connector).
See next chapter

Air valve defect

Disabled in s.w.
version 4.30 for old
CPU board !!

Enabled in V5.00.10
of new CPU board.
Disabled again in
s.w. version V6.00.10

Missing feedback signal from one or both
microswitches on the air valve (vent).

Position switch(es) loose.
Position switch(es) defect.
Position switch(es) wrong adjusted.
Camshaft loose (does not rotate).
Airvalve motor broken.
Airvalve blocked.
Loose wiring of switches or motor.
Both switches are activated.

Water drain defect

Missing feedback signal for the cleaning
position of the 3-way valve

Broken switches inside the valve housing.
Broken or loose relay K8.
Wiring problem

Grease drain defect

Missing feedback signal for the cooking
position of the 3-way valve

Broken switches inside the valve housing.
Broken or loose relay K7.
Wiring problem

Fan guard fails

Disabled in s.w. ver-
sion V5.01.03 !!

Too less or no heat distribution to the
cooking cavity

The blower is not rotating while it should.
Defect vane switch(es).
broken heating elements

Other messages

Description

Possible causes

Door open

The door is opened during the
cooking proces

The door is open

Malfunction of doorswitch.

Lime filter full

Disabled in sw ver-
sion 4.32 for old
CPU board only!!

The lime filter needs to be
replaced and in the manager
menu, the parameter “lime
filter replaced” needs to be
put on “yes”

The maximum amount of water has been used and a
new filter cartridge needs to be placed.
The water capacity setting in the service menu is wrong.
No filter is connected. The water capacity setting has to

be set to”

-

” in the service menu.

ERROR MESSAGES

TROUBLE SHOOTING

«
...
75
76
77
78
79
...
»

Содержание Deli Multisserie





































































































































Отзывы:

Нет отзывов

Похожие инструкции для Deli Multisserie

Бренд: NAD Страницы: 10

Бренд: Keithley Страницы: 42

Бренд: 3M Страницы: 48

Бренд: 3M Страницы: 19

Бренд: Abbott Страницы: 2

FreeStyle Libre

Бренд: Abbott Страницы: 3

Бренд: abc Страницы: 8

Бренд: Eagle Eye Страницы: 21

Бренд: Labomed Страницы: 67

Бренд: Hach Страницы: 456

Бренд: JBL Страницы: 17

Бренд: ACS Страницы: 28

Бренд: ABB Страницы: 154

Бренд: ATD Tools Страницы: 7

Бренд: Wecan Technology and Lighting Co., Ltd Страницы: 4

Ology Walkstation 1451458001

Бренд: Steelcase Страницы: 38

Бренд: WAGNER Страницы: 31

CB Ohio Special 100 HP

Бренд: CleaverBrooks Страницы: 200

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды