Fri-Jado Deli Multisserie Скачать руководство пользователя страница 30

Страница: 30 / 132

REMOVAL AND REPLACEMENT OF PARTS

Page 30

Service Manual Deli Multisserie form 9123667 rev. 20220317

16.Disconnect the wiring from the 2 screw

terminals on the blower motor(s) and cut
the cable tie.

17.Remove the 4 nuts (M6 serrated) from the

aluminium motor-housing and carefully
take out the blower [50]. Repeat this if
necessary with the other blower.

Refer to the concerning chapter to assemble
the blowers.

Keep blower motor and fan blade together!!

DISASSEMBLING THE SHAFT TRANSIT SPACER.

Remove the blowers and shaft seals accor-

ding prior procedure.

On the backside.
18. Remove the 4 bolts (M5x10) on the cor-

ners of the mounting plate. [255].

19. Stab loose the mounting plate with a

screw driver (or the like). (The spacer [254)
is sealed at the front side with sealant and
can possibly stick)

20. Pull the mountingplate with the spacer

out of the hole.

21. Remove the mounting plate from the

spacer (3 bolts M5x12).

Содержание Deli Multisserie





































































































































Результаты поиска

Содержание Deli Multisserie

Отзывы:

Похожие инструкции для Deli Multisserie

Бренды по названию

Популярные бренды

Fri-Jado Deli Multisserie, Руководство по обслуживанию

Результаты поиска

Содержание Deli Multisserie

Отзывы:

Похожие инструкции для Deli Multisserie

Бренды по названию

Популярные бренды