Fri-Jado Deli Multisserie Скачать руководство пользователя страница 83

Страница: 83 / 132

TROUBLE SHOOTING

Page 83

Service Manual Deli Multisserie form 9123667 rev. 20220317

Description of part

Symptoms

Possible cause

Action

Sensor

Temperature read-out on
LCD is not stable.

Upper sensor defect.
Wire loose.

Check sensor and wiring.
See also input test in
service menu

Product over cooked.
Cooking takes more time.
Uneven cooking.

Upper or lower sensor de-
fect. (resistance too low)

Check sensor and wiring.
See also input test in
service menu

Cooking takes more time

Upper or lower sensor de-
fect. (resistance too high).

Check sensor and wiring.
See also input test in
service menu

Uneven cooking (difference
between lower and higher
racks)

Upper or lower sensor
defect.
Offset parameter not
right adjusted. See service
menu.

Check sensor and wiring.
See also input test and
parameters in service
menu.

Sliding contact (on
rotor)

Baking program ends too
soon

Bad or no contact (resi-
stance too high).

Clean contact or replace.

Illumination

Less display effect

One or more lamps defect
Calcifying or greasing of
lamp glasses
Broken lamp gasket

Replace lamps.
Clean or replace lamp
glasses.
Replace gasket

Air exhaust valve (Vent)

Steam blows along the
doorgaskets.
Trumpet sound when clo-
sing the door
Whisle sound at the exhaust
Product too wet
Product too dry

Air exhaust valve clogged
Air Exhaust valve mal-
function

Check and or clean ex-
haust pipe and valve
Check valve motor
Check position switches
on valve motor

Watervalve

Product too dry.
Product too wet.
Product not well proofed.
(Bake version).
Cleaning not ok.

Watervalve coil defect.
Filter clogged.
Dirt in watervalve.
Reducer in watervalve
clogged.
Reducer in watervalve not
well mounted.

Check coil.
Clean valve if possible.
Replace valve AND redu-
cer.

Water supply

Product too dry.
Product not well proofed.
(Bake version).
Cleaning not ok.

Water tap closed.
Water pressure too low
(<2bar).
Filters blocked.
Kink in hose.

Open tap.
Check pressure.
Check filters
Search for a kink in the
hose.

Tubes calcified

Product too dry.
Product not well proofed.
(Bake version)

Supply water not decal-
cified.
Decalcifying equipment
not ok.
Decalcifying filter satura-
ted.

Check water hardness.

Change filter.

Door switch

Message door open appears
while door is closed

Reed contact door shor-
ted.
Wiring shorted.

Check reed contact and/
or wiring. Replace if
necessary

Blowers,heaters and ro-
tor stay on while door is
opened.

Reed contact defect.
Wiring loose.

Check reed contact and/
or wiring. Replace if
necessary

Содержание Deli Multisserie





































































































































Результаты поиска

Содержание Deli Multisserie

Отзывы:

Похожие инструкции для Deli Multisserie

Бренды по названию

Популярные бренды

Fri-Jado Deli Multisserie, Руководство по обслуживанию

Результаты поиска

Содержание Deli Multisserie

Отзывы:

Похожие инструкции для Deli Multisserie

Бренды по названию

Популярные бренды