Fresenius Vial INJECTOMAT 2000 Anasthesie Скачать руководство пользователя страница 64

Страница: 64 / 82

Page : 60

NT 0928 Rev.A0

5.16.3. Operating mode

Remark: the software works following the operating mode described in the Pr EN 60-601-2-24

Standard for infusion pumps.

1. Start the acquisition program for the scales.

2. Enter the data necessary to carry out the program without validating the flow rate.

3. Adjust the scales to the specified flow rate.

4. Confirm the flow rate on the microcomputer so that the automatic setting of the scales can take

place.

5. Start infusion when 00.00 appears on the scales display screen.

6. When the specified time is over, note the error percentage displayed on the screen.

5.16.4. Installation drawing

5.17. Flow rate control: flow rate control measurement with scales

In compliance with IEC 601.2 standard, 2nd part - 62D standard project for infusion pumps.

5.17.1. Equipment used:

Stop clock

Scales - scales sensitivity:

flow rate value (x)

scale sensivity

≤

5 ml/h

1/10000e

5 ml/h < x

≤

30 ml/h

1/1000e

x > 30 ml/h

1/100e

Test tube or beaker with 1 ml graduating

Liquid: distilled water +/ oil)

Luer Lock type plastic syringe (50 or 20 ml)

Catheter extension with Luer Lock end piece (length 100 cm, inside diameter 2.5 mm)

Needle:

flow rate value (x)

needle type

x < 30 ml/h

G 26

≤

30 ml/h

G 18 ou G 21

catheter extension support stand

RS 232 cord

anti-vibration measurement table

Содержание INJECTOMAT 2000 Anasthesie



















































































Результаты поиска

Содержание INJECTOMAT 2000 Anasthesie

Отзывы:

Бренды по названию

Популярные бренды

Fresenius Vial INJECTOMAT 2000 Anasthesie, Техническое руководство

Результаты поиска

Содержание INJECTOMAT 2000 Anasthesie

Отзывы:

Бренды по названию

Популярные бренды