Fresenius Vial INJECTOMAT 2000 Anasthesie Скачать руководство пользователя страница 25

Страница: 25 / 82

NT 0928 Rev.A0

page : 21

2.2.1.6.1. Opto switch body syringe measurement.

Note: The CI opto and the obturator are specific to the Injectomat 2000 Anästhesie equipped

with "flange detector" and are not compatible with previous versions.

2 opto devices allow to detect 2 syringe sizes: 60 cc and 20 cc.

J2.1

opto diode +5V anode

J2.2

opto cathode common point and transistor transmitter

J2.3

opto 1 transistor collector

J2.4

opto 2 transistor collector

Control signal:

CODPT3

activate at 1

driven by microprocessor line T0.

Output signal:

SOPT4

activate at 1

Output signal:

SOPT3

activate at 1

SOPT3

SOPT4

Syringe clamp detection alarm, high position

60 cc detection

20 cc detection

Syringe clamp detection alarm, low position

The motor rotation and piston presence opto switch interfaces are located on the POWER SUPPLY
BOARD.

2.2.1.6.2. Motor rotation opto switch

Control signal:

CDOPT1

activate at 1

Output signal:

SOPT1

activate at 1

2.2.1.6.3. Piston presence opto switch (anti-siphon)

Control signal:

CDOPT2

activate at 1

Output signal:

SOPT2

activate at 1

2.2.2. Description of connectors

2.2.2.1. J1 not used

This connector is not used for the moment but it will be used for a future evolution of the software.

2.2.2.2. J2 Opto switch - syringe body connector

Pin

Description

ground

flange switch

opto +5 V diode anode

cathode diode transmitter transistor opto 1 and opto 2 common points

collector transistor opto 1

collector transistor opto 2

Содержание INJECTOMAT 2000 Anasthesie



















































































Результаты поиска

Содержание INJECTOMAT 2000 Anasthesie

Отзывы:

Бренды по названию

Популярные бренды

Fresenius Vial INJECTOMAT 2000 Anasthesie, Техническое руководство

Результаты поиска

Содержание INJECTOMAT 2000 Anasthesie

Отзывы:

Бренды по названию

Популярные бренды