Fresenius Medical Care 5008 Скачать руководство пользователя страница 238 | Manualshive

Страница: 238 / 328

Fresenius Medical Care 5008 Скачать руководство пользователя страница 238

Chapter 11: System Description

11-28

Fresenius Medical Care 5008 OP 5/09.06

O

Description

Description of the
procedure

OCM measurement technique

An Online Clearance Measurement is performed at different times
during a dialysis treatment to determine the clearance over time and to
detect a reduction in efficiency that occurred during the treatment. The
measurement can be started by the operator on the dialysis system or
can be programmed in the SETUP to start with each dialysis treatment.

During an Online Clearance Measurement the conductivity of the
dialysate flowing into the dialyzer is adjusted in accordance with a fixed
time schedule. If the base conductivity is within 13.9 to 14.6 mS/cm, the
measurement direction will alternate, otherwise the variations will
always be performed in the same direction.

A pre- and post-dialyzer measurement of the conductivity is performed
by two mutually independent temperature-compensated conductivity
cells.

Sequence of measuring cycles during treatment

The interval between two measurements can be freely selected in
increments of 1 minute. The minimum interval is 25 minutes. No
measurement will be started if only 12 minutes are left until completion
of the UF time.

If an OCM measurement is aborted, e.g. by changing one of the dialysis
parameters, the measurement will be repeated at the next possible
occasion.

Conductivity limits during a measurement

To prevent a conductivity alarm, the CD window will automatically and
temporarily be spread while a measurement is in progress.

Changing the concentrate settings during a CD variation

The current desired conductivity should not be changed during the CD
variation as this would cause the measurement to be aborted and to be
repeated later.

11.5.6 ONLINE

plus

™ Description

The term "ONLINE" means that the substitution fluid is produced from
the dialysate during the treatment. Both procedures (HDF and HF) can
be performed as predilution (pre-dialyzer addition of the substituate)
and postdilution (post-dialyzer addition of the substituate).

With the ONLINE

plus

™ option the substituate for the treatment modes

HDF and HF "ONLINE" is derived from the dialysate by means of two
filter stages and a substituate pump and is infused into the patient. As
the patient is connected via the dialyzer (High-Flux) to the closed
dialysate circuit of the dialysis system, the volume balance remains
neutral. Fluid is therefore removed from the patient by the UF pump
only.

Note

It must always be ensured that the CD limits are set symmetrically.

«
...
236
237
238
239
240
...
»

Содержание 5008









































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды