manualshive.com logo in svg

Fresenius Medical Care 5008, Руководство по эксплуатации

Поделиться
Скачать
Fresenius Medical Care 5008 Скачать руководство пользователя страница 226

Chapter 11:  System Description

11-16

Fresenius Medical Care 5008 OP 5/09.06

11.2 Storage

The hemodialysis system must be stored vertically in a well-ventilated 
room with low variations in temperature.

Temperature

Without antifreeze: +5 °C to +60 °C
With antifreeze: –20 °C to +60 °C

Relative humidity

30 % to 75 %, temporarily 95 %

Atmospheric pressure

500 hPa to 1060 hPa

Antifreeze

When storing the hemodialysis system with antifreeze, make sure to 
use antifreeze of the following composition:
– 49.875 % water
– 49.875 % glycerine
– 0.25 % ClearSurf™

Maintenance of the 
integrated battery

Upon receipt of the system, charge the battery as follows:
– Use the power cable to connect the system to the electrical power 

source.

– Actuate the power switch to turn the system on.
– Leave the system on for 10 hours.

If the system is not used, repeat this procedure every six months.

11.3 Transportation

O

Inside buildings

Release the brake

The hemodialysis system can be swiveled, turned or pushed in any 
direction.

To get over uneven surfaces (e.g. elevator entry):
To avoid damage or prevent the machine from toppling over always 
push the hemodialysis system slowly over uneven surfaces.

To go up and down steps/stairs:
To go up and down steps/stairs at least two persons are required.

Procedure:
Transport protection for the monitor support arm. (Tighten the screw.)
Apply the brake
Close the vent tubing.
Lift the machine for transportation. When lifting the system never hold it 
by the IV pole, the handle or one of the system components (e.g. EBM 
doors).

Содержание 5008









































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды