manualshive.com logo in svg

Fresenius Kabi Ambix activ, Инструкция по эксплуатации

Поделиться
Скачать
Fresenius Kabi Ambix activ Скачать руководство пользователя страница 21

21

3.4.6

Start pumping

  

3.4.7

Stop pumping

  

  

3.4.8

Stop a program

  

3.4.9

Information button

   

3.4.10

Silence an alarm 

 

Press the Start button to start administration.

Warning

For sets with a drip chamber, please check that the roller clamp is 

opened and that liquid is flowing into the drip chamber.

Press the Stop/Esc button to stop administration.

Information

The Stop/Esc button is also used to clear alarms. In some 
screens, the Stop/Esc button will also function as an escape 

button to escape from an unwanted display or parameter setting 

procedure.

Once a program is started, it is impossible to change values. To abort a 

program, the pump has to be switched off. After switching the pump on 

again, a new program can be set and started.

By pressing the i/OK button the total volume infused since the last reset 

will be displayed for 5 seconds ( 

 

will be shown in the display). If the 

pump is running and the target volume is activated, the remaining 

volume will then be displayed ( 

 

will be shown in the display).

When the pump is not pumping, pressing the i/OK button for more than 

3 seconds resets the display of the administered volume to zero.

Information

Further functions of the info button are described in the relevant 
sections below

.

Alarms can be silenced for 2 minutes by pressing the Alarm silence 
button (

). During this period the alarm reminder will only be indicated 

by flashing of the display. It is possible to re-start administration by 
pressing the Start button.

Содержание Ambix activ

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды