manualshive.com logo in svg

Fresenius Kabi Ambix activ, Инструкция по эксплуатации

Поделиться
Скачать
Fresenius Kabi Ambix activ Скачать руководство пользователя страница 19

19

3.3.2

Removing the set

  

 

3.4

Operating the Ambix 

activ

3.4.1

Switch pump on

 

 

3.4.2

Switch pump off

If the pump is running, stop the infusion by pressing the STOP/ESC 
button. 

1.

Switch the pump OFF by holding the On/Off button down for more 

than 3 seconds.

2.

Ensure that backflow from the patient access system is prevented, if 

present, close the roller clamp, and disconnect the set from the 

patient.

3.

Open the pump door – the 

activ

 clamp will be automatically closed. 

Remove the set starting with the green adapter.

4.

Dispose of the set following appropriate legislation and local 

procedures.

5.

If it is required to restart the pump, repeat the installation procedure 

described above in Section 3.3.1, page 18.

Press the On/Off button for more than one second to switch the pump 

on. The pump will boot and will perform a self test. The most recent 

parameters and program will be shown in the display.

Press the On/Off button for more than three seconds to switch the pump 

off. The display will count down, 3-2-1-off, and the pump will then shut 

down. Parameters from the most recent infusion will be retained in the 

pump’s memory. This information is saved for 1 month following the last 

switch-off, provided the battery was fully charged at switch off. 

This operation is possible when the pump is not running (for example, 

after the end of infusion programmed or at stopping of the infusion by 

pressing the STOP/ESC button).

Содержание Ambix activ

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды