manualshive.com logo in svg

Freescale Semiconductor PXR4030, Справочное руководство

Поделиться
Скачать
Freescale Semiconductor PXR4030 Скачать руководство пользователя страница 541

Enhanced Direct Memory Access Controller (eDMA)

Freescale Semiconductor

21-17

PXR40 Microcontroller Reference Manual, Rev. 1

21.3.2.2

eDMA Error Status Register (EDMA_x_ESR)

The EDMA_

x

_ESR provides information about the last recorded channel error. Channel errors can be 

caused by a configuration error (an illegal setting in the transfer control descriptor or an illegal priority 
register setting in fixed-arbitration mode) or an error termination to a bus master read or write cycle.

A configuration error is caused when the starting source or destination address, source or destination 
offsets, minor loop byte count, and the transfer size represent an inconsistent state. The addresses and 
offsets must be aligned on 0-modulo-transfer_size boundaries, and the minor loop byte count must be a 
multiple of the source and destination transfer sizes. All source reads and destination writes must be 
configured to the natural boundary of the programmed transfer size respectively. 

In fixed-arbitration mode, a configuration error is generated when any two channel priority levels are equal 
and any channel is activated. The ERRCHN field is undefined for this type of error. All channel priority 
levels must be unique before any service requests are made.

If a scatter-gather operation is enabled on channel completion, a configuration error is reported if the 
scatter-gather address (DLAST_SGA) is not aligned on a 32-byte boundary. If minor loop channel linking 
is enabled on channel completion, a configuration error is reported when the link is attempted if the 
EDMA

_x

_TCD.CITER.E_LINK bit is not equal to the EDMA

_x

_TCD.BITER.E_LINK bit. All 

configuration error conditions except scatter-gather and minor loop link error are reported as the channel 
is activated and assert an error interrupt request if enabled. When properly enabled, a scatter-gather 
configuration error is reported when the scatter-gather operation begins at major loop completion. A minor 
loop channel link configuration error is reported when the link operation is serviced at minor loop 
completion.

If a system bus read or write is terminated with an error, the data transfer is immediately stopped and the 
appropriate bus error flag is set. In this case, the state of the channel’s transfer control descriptor is updated 
by the DMA engine with the current source address, destination address, and minor loop byte count at the 
point of the fault. If a bus error occurs on the last read prior to beginning the write sequence, the write is 
executed using the data captured during the bus error. If a bus error occurs on the last write prior to 
switching to the next read sequence, the read sequence is executed before the channel is terminated due to 
the destination bus error.

A transfer may be cancelled by software via the EDMA_

x

_MCR[CX] bit. When a cancel transfer request 

is recognized, the eDMA engine stops processing the channel. The current read-write sequence is allowed 
to finish. If the cancel occurs on the last read-write sequence of a major or minor loop, the cancel request 
is discarded and the channel retires normally. 

The error cancel transfer is the same as a cancel transfer except the DMAES register is updated with the 
cancelled channel number and error cancel bit is set. The TCD of a cancelled channel has the source 
address and destination address of the last transfer saved in the TCD. It is the responsibility of the user to 
initialize the TCD again should the channel need to be restarted because the aforementioned fields have 
been modified by the eDMA engine and no longer represent the original parameters. When a transfer is 
cancelled via the error cancel transfer mechanism (setting the EDMA_

x

_MCR[ECX]), the channel 

number is loaded into the EDMA_

x

_ESR[ERRCHN] field and the EDMA_

x

_ESR[ECX] and 

EDMA_

x

_ESR[VLD] bits are set. In addition, an error interrupt may be generated if enabled. Refer to 

Section 21.3.2.14, eDMA Error Registers (EDMA_x_ERH, EDMA_x_ERL).

Содержание PXR4030



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды