Fondital Antea 24kW Range Скачать руководство пользователя

Страница: 54 / 60

BOILER STATUS

MALfUNCTION

PROBABLE CAUSE

SOLUTION

Boiler in shutdown state, fault
code E01 shown on LCD display.
Press the Reset button to restore
operation.

Burner does not ignite

Gas supply failure

Check gas supply
Check gas supply cock or gas
network safety valve intervention

Gas valve is disconnected

Reconnect it

Gas valve is faulty

Replace it

PCB is faulty

Replace it

Burner does not ignite: there is

no spark

Ignition/detection electrode
faulty

Replace the electrode

Ignition transformer faulty.

Replace the ignition transformer.

Electronic board does not
switch on: it is faulty

Replace PCB

Burner ignites for a few seconds

and goes off

Electronic board does not detect
flame: inverted phase and neutral

Verify correct neutral and phase
connection

Ignition/detection electrode wire
is interrupted

Reconnect or replace wire

Ignition/detection electrode
faulty

Replace the electrode

Electronic board does not detect
flame: it is faulty

Replace PCB

Ignition heat output setting is too
low

Increase it

Minimum heat output is not set
correctly

Check burner setting

Boiler in shutdown state, fault
code E03 shown on LCD display.
Press the Reset button to restore
operation.

One of the flue gas thermostats

has tripped.

Poor flue draught

Check the chimney and ambient
air suction openings.

Flue gas thermostat is faulty

Replace it

Fault code E04 shown on LCD
display.
Normal operation is restored
automatically when the faults
causing the alarm state are
rectified.

CH system water pressure is low

There are leaks in the heating
system

Check system for leaks

Water pressure switch is
disconnected

Reconnect it

Water pressure switch is not
operating: it is faulty

Replace it

Fault code E05 shown on LCD
display.
Normal operation is restored
automatically when the faults
causing the alarm state are
rectified.

flow probe not

working.

Flow probe disconnected.

Reconnect it

Flow probe faulty.

Replace it

10.

TABLE Of fAULT CODES

Содержание Antea 24kW Range





























































Результаты поиска

Содержание Antea 24kW Range

Отзывы:

Похожие инструкции для Antea 24kW Range

Бренды по названию

Популярные бренды

Fondital Antea 24kW Range, Руководство по установке, использованию и обслуживанию

Результаты поиска

Содержание Antea 24kW Range

Отзывы:

Похожие инструкции для Antea 24kW Range

Бренды по названию

Популярные бренды