Fluke ScopeMeter 19 B Series Скачать руководство пользователя страница 82

Страница: 82 / 86

Fluke 19xB-19xC-2x5C

Service Manual

6-6

Referring to Figure 6-5, use the following procedure to remove the main PCA unit.
1.

Open the test tool (see Section 6.2.4).

Disconnect the blue keypad foil (item 5) flat cable, and the white LCD (item 7) flex

cable. Unlock each cable by lifting the connector latch at the left and right edge

using a small screw-driver, see Figure 6-6. The latch remains attached to the

connector body.

ST8682.WMF

Figure 6-6. Flex Cable Connectors

Unplug the two-wire backlight cable.

Warning

If the battery pack or the power adapter is connected, the LCD

backlight voltage on the wire cable is 400V ! (when the test tool

is on).

Remove the two screws (item 14) that secure the Main PCA unit to the top case.

Slide the Main PCA unit in the input cover direction to remove it.

To remove the fan from the main PCA unit, unplug the fan connector and unscrew

the screws item 24.

6.2.6 Removing the Display Assembly

There are no serviceable parts in the display assembly. Referring to Figure 6-5, use the

following procedure to remove the display assembly.
1.

Remove the main PCA unit (see Section 6.2.5).

Unscrew the four screws item 10.

Remove the display assembly (item 7) with the mounting frame (item 8).

To prevent finger contamination, wear cotton gloves, or handle the display assembly

by its edges.

Remove the display from the mounting frame.

Содержание ScopeMeter 19 B Series























































































Результаты поиска

Содержание ScopeMeter 19 B Series

Отзывы:

Бренды по названию

Популярные бренды

Fluke ScopeMeter 19 B Series, Руководство по обслуживанию

Результаты поиска

Содержание ScopeMeter 19 B Series

Отзывы:

Бренды по названию

Популярные бренды