Fluke ScopeMeter 19 B Series Скачать руководство пользователя страница 62

Страница: 62 / 86

Fluke 19xB-19xC-2x5C

Service Manual

5-6

5.4 Contrast Calibration Adjustment

After entering the calibration mode the display shows:

WarmingUp (CL 0200):IDLE (valid)

Do not press

now! If you did, turn the test tool off and on, and enter the

calibration mode again.
Proceed as follows to adjust the maximum display darkness (CL 0100), the default

contrast (CL 0110) , and the maximum display brightness (CL 0120).

Press

three times to select maximum darkness calibration

Contrast (CL 0100):

Press

CALIBRATE

. The display will show a dark test pattern, see Figure 5-2

Using

adjust the display to the maximum darkness at which the test pattern

is only just visible.

Press

to return to the softkey menu.

Press

to select default contrast calibration

Contrast (CL 0110):

Press

CALIBRATE

. The display shows the test pattern at default contrast.

Using

set the display to optimal (becomes default) contrast.

Press

to return to the softkey menu.

Press

to select maximum brightness calibration

Contrast (CL 0120):

10.

Press

CALIBRATE

. The display shows a bright test pattern.

11.

Using

adjust the display to the maximum brightness, at which the test pattern

is only just visible.

12.

Press

to return to the softkey menu.

13.

Now you can either

•

Exit, if only the Contrast had to be adjusted. Continue at Section 5.7.

•

Do the complete calibration. Press

to select the next step (WarmingUp),

and continue at Section 5.5.

Figure 5-2. Display Test Pattern

Содержание ScopeMeter 19 B Series























































































Результаты поиска

Содержание ScopeMeter 19 B Series

Отзывы:

Бренды по названию

Популярные бренды

Fluke ScopeMeter 19 B Series, Руководство по обслуживанию

Результаты поиска

Содержание ScopeMeter 19 B Series

Отзывы:

Бренды по названию

Популярные бренды