Fluke ScopeMeter 19 B Series Скачать руководство пользователя страница 49

Страница: 49 / 86

Performance Verification

4.6 Scope Input A&B Tests

4-25

Proceed as follows:
1.

Connect the test tool to the calibrator as shown in Figure 4-16.

al55sca.bmp

Figure 4-16. Test Tool Input A to TV Signal Generator

Select the following test tool setup:

•

Reset the test tool

•

Press

, then press

to open the Trigger Options menu.

•

Choose

VIDEO on A...

, then from the shown opened menu choose

Polarity: POSITIVE | PAL

(

NTSC PALplus SECAM

)

•

Press

to select

ALL LINES

•

Press

to enable the arrow keys for selecting the video line number.

•

Using

select line number:

⇒

622 for PAL, PALplus, or SECAM

⇒

525 for NTSC.

•

Using

and

set the Input A sensitivity to 2 V/div (the actual probe setting

is 10:1).

•

Using

select the time base to 20

s/div.

Set the calibrator to mode video with amp100%. Set format and marker line
number to :

⇒

PAL 622 (even), for PAL and PALplus

⇒

SECAM 622 (even), for SECAM

⇒

NTSC 262 even, for NTSC.

Observe the trace, and check to see if the test tool triggers on the negative pulse
before the marker pulse (see Figure 17).

Содержание ScopeMeter 19 B Series























































































Результаты поиска

Содержание ScopeMeter 19 B Series

Отзывы:

Бренды по названию

Популярные бренды

Fluke ScopeMeter 19 B Series, Руководство по обслуживанию

Результаты поиска

Содержание ScopeMeter 19 B Series

Отзывы:

Бренды по названию

Популярные бренды