manualshive.com logo in svg

Fluke ScopeMeter 19 B Series, Руководство по обслуживанию

Поделиться
Скачать
Fluke ScopeMeter 19 B Series Скачать руководство пользователя страница 51

 

Performance Verification

 

 

4.7 External Trigger Level Test

 

4

 

  

4-27 

4.7 External Trigger Level Test 

Proceed as follows: 
1.

 

Connect the test tool to the 5500A as shown in Figure 4-18. 

 

al55ex2w.bmp 

Figure 4-18. Test Tool Meter/Ext Input to 5500A Normal Output 

2.

 

Select the following test tool setup: 

•

 

Reset the test tool 

•

 

Press 

  

•

 

Using 

 select the 

TRIGGER OPTIONS...

 menu 

⇒

 

Select   

On Edges...

 from the 

TRIGGER OPTIONS

 menu 

⇒

 

Select 

Update:   Single Shot | Noise reject Filter:   On

 

•

 

Using 

 

EDGE TRIG

 select 

Ext

 . 

•

 

Using 

 

SLOPE

 select positive slope triggering (trigger icon   ). 

•

 

Using 

 

Ext LEVEL

 select 

1.2 V

  

3.

 

Set the 5500A to source 0.4V dc. 

4.

 

Verify that no trace is shown on the test tool display, and that the status line at the 
display top shows 

SINGLE MANUAL 

or 

SINGLE WAITING

.  If the display shows the 

trace, and status 

SINGLE HOLD

 then press 

 to re-arm the test tool for a trigger. 

5.

 

Set the 5500A to source 1.7 V 

6.

 

Verify that the test tool is triggered by checking that the trace becomes visible. 
To repeat the test, start at step 3. 

7.

 

Set the 5500A to Standby. 

Содержание ScopeMeter 19 B Series























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды