manualshive.com logo in svg

Fluke ScopeMeter 19 B Series, Руководство по обслуживанию

Поделиться
Скачать
Fluke ScopeMeter 19 B Series Скачать руководство пользователя страница 47

 

Performance Verification

 

 

4.6 Scope Input A&B Tests

 

4

 

  

4-23 

•

 

sync pulse amplitude > 0.7 div. 

•

 

chroma amplitude zero. 

4.

 

Observe the trace, and check to see if the test tool triggers on line number: 

⇒

 

622 for PAL or SECAM, see Figure 4-9 

⇒

 

525 for NTSC, see Figure 4-10. 

 

Figure 4-9. Trace for PAL/SECAM line 622 

 

Figure 4-10. Trace for NTSC line 525 

5.

 

Using 

 select line number: 

⇒

 

310 for PAL or SECAM 

⇒

 

262 for NTSC 

6.

 

Observe the trace, and check to see if the test tool triggers on: 

⇒

 

line number 310 for PAL or SECAM, see Figure 4-11. 

⇒

 

line number 262 for NTSC, see Figure 4-12. 

 

Figure 4-11. Trace for PAL/SECAM line 310 

 

Figure 4-12. Trace for NTSC line 262 

7.

 

Apply the inverted TV Signal Generator signal to the test tool.   
Invert the signal by using a Banana Plug to BNC adapter (Fluke PM9081/001) and a 
Banana Jack to BNC adapter (Fluke PM9082/001), as shown in Figure 4-13. 

Содержание ScopeMeter 19 B Series























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды