manualshive.com logo in svg

Fluke ScopeMeter 19 B Series, Руководство по обслуживанию

Поделиться
Скачать
Fluke ScopeMeter 19 B Series Скачать руководство пользователя страница 44

Fluke 19xB-19xC-2x5C 

Service Manual 

4-20 

4.6.11 Input B Trigger Sensitivity Test 

Proceed as follows to test the Input B trigger sensitivity: 
1.

 

Connect the test tool to the 5500A as shown in Figure 4-7. 

 

al55scb.bmp 

Figure 4-7. 5500A Scope Output to Test Tool Input B 

2.

 

Select the following test tool setup: 

•

 

Reset the test tool 

•

 

Press 

 and use 

 to turn Input B on. 

•

 

Press 

 and use 

 to turn Input A off. 

•

 

Using 

 move the Input B trace zero to the center grid line. 

•

 

Press 

 and use 

 to select Input B as trigger source. 

•

 

Using 

 and 

 change the sensitivity range to select manual sensitivity 

ranging, and lock the Input B sensitivity range on 2 V/div. 

3.

 

Using 

 select the time base indicated under the first column of Table 4-10. 

4.

 

Set the 5500A to source the leveled sine wave given in the first row of Table 4-10. 

5.

 

Adjust the 5500A output voltage until the displayed trace has the amplitude indicated 
under the appropriate column of Table 4-10. 

6.

 

Verify that the signal is well triggered.  
If it is not, press 

 , then using 

 enable the up/down arrow keys for manual 

Trigger Level adjustment.  Adjust the trigger level and verify that the signal will be 
triggered now.  The trigger level is indicated by the trigger icon ( ). 

7.

 

Continue through the test points. 

8.

 

When you are finished, set the 5500A to Standby. 

Содержание ScopeMeter 19 B Series























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды