manualshive.com logo in svg

Fluke ScopeMeter 19 B Series, Руководство по обслуживанию

Поделиться
Скачать
Fluke ScopeMeter 19 B Series Скачать руководство пользователя страница 75

 

Calibration Adjustment

 

 

5.8 Probe Calibration

 

5

 

  

5-19 

5.8 Probe Calibration 

To meet full user specifications, you need to adjust the supplied red and gray VPS200 

voltage probes for optimal response. 
To adjust the VPS200 probes, do the following: 
1.

 

Connect the red probe from the red Input A BNC to the banana jacks.  See figure 5-9 

 

ST8416.WMF 

 

 

 

ST7991.WMF 

 

Figure 5-9. 10:1 Probe Calibration Connection 

Figure 5-10. 10:1 Probe Calibration 

2.

 

Press 

 , and then 

 to open the 

Probe on A

 menu 

3.

 

Select Probe Type:   

Voltage | Attenuation:   10:1 ,   Probe Cal...

  

4.

 

Press 

 to start the probe calibration.  A square wave appears on the screen. See 

Figure 5-10  (the lower half of the screen is covered with operating instructions). 

5.

 

Adjust the trimmer screw in the probe housing until a pure square wave is displayed. 

6.

 

Press  

 to continue with automatic dc calibration. 

The test tool automatically calibrates itself to the probe.  A message indicates that he 
dc calibration has been completed successfully. 

7.

 

Repeat the procedure for the gray VPS200 probe, connected from the gray Input B 
BNC to the banana jacks. 

 

Содержание ScopeMeter 19 B Series























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды