Fluke ScopeMeter 19 B Series Скачать руководство пользователя страница 55

Страница: 55 / 86

Performance Verification

4.8 Meter (DMM) Tests

4-31

al55ex4w.bmp

Figure 4-19. Test Meter Tool Input to 5500A Normal Output 4-Wire

Select the following test tool setup:

•

Press

•

Press

to open the Measurement menu, and select

Ohms

•

Press

to select AUTO ranging.

Set the 5500A to source the appropriate resistance value for the first test point in
Table 4-14.
Use the 5500A “COMP 2 wire” mode for the verifications up to and including
50 k

. For the higher values, the 5500A will turn off the “COMP 2 wire” mode.

Observe the reading and check to see if it is within the range shown under the
appropriate column.

Continue through the test points.

When you are finished, set the 5500A to Standby.

Table 4-14. Resistance Measurement Verification Points

5500A output

Meter Reading

0.0 to 0.5

400

397.1 to 402.9

4 k

3.971 to 4.029

40 k

39.71 to 40.29

400 k

397.1 to 402.9

4 M

3.971 to 4.029

30 M

29.77 to 30.23

Содержание ScopeMeter 19 B Series























































































Результаты поиска

Содержание ScopeMeter 19 B Series

Отзывы:

Бренды по названию

Популярные бренды

Fluke ScopeMeter 19 B Series, Руководство по обслуживанию

Результаты поиска

Содержание ScopeMeter 19 B Series

Отзывы:

Бренды по названию

Популярные бренды