Fluke ScopeMeter 19 B Series Скачать руководство пользователя страница 11

Страница: 11 / 86

Safety Instructions

1.1 Introduction

1-3

1.1 Introduction

Read these pages carefully before beginning to install and use the test tool.
The following paragraphs contain information, cautions and warnings which must be

followed to ensure safe operation and to keep the test tool in a safe condition.

Warning

Servicing described in this manual is to be done only by

qualified service personnel. To avoid electrical shock, do not

service the test tool unless you are qualified to do so.

1.2 Safety Precautions

For the correct and safe use of this test tool it is essential that both operating and service

personnel follow generally accepted safety procedures in addition to the safety

precautions specified in this manual. Specific warning and caution statements, where they

apply, will be found throughout the manual. Where necessary, the warning and caution

statements and/or symbols are marked on the test tool.

1.3 Caution and Warning Statements

Caution

Used to indicate correct operating or maintenance procedures

to prevent damage to or destruction of the equipment or other

property.

Warning

Calls attention to a potential danger that requires correct

procedures or practices to prevent personal injury.

1.4 Symbols

The following symbols are used on the test tool, in the Users Manual, in this Service

Manual, or on spare parts for this test tool.

See explanation in Users Manual

DOUBLE INSULATION (Protection
Class)

Live voltage

Earth Ground

Static sensitive components
(black/yellow).

Recycling information

Do not dispose of this product
as unsorted municipal waste. Go to
Fluke's website for recycling
information.

Conformité Européenne

Safety Approval

Содержание ScopeMeter 19 B Series























































































Результаты поиска

Содержание ScopeMeter 19 B Series

Отзывы:

Бренды по названию

Популярные бренды

Fluke ScopeMeter 19 B Series, Руководство по обслуживанию

Результаты поиска

Содержание ScopeMeter 19 B Series

Отзывы:

Бренды по названию

Популярные бренды