B614
45
732998 - Rev.A_DRAFT
Tr
ansla
tion of the original instruc
tions
ENGLISH
10.3
RADIO MODULE XF
E614 is fitted with an OMNIDEC integrated two channel
decoding system that can memorise, via the XF radio
module, FAAC radio remote controls that use the fol-
lowing types of radio code: SLH/SLH LR, LC/RC, DS.
The three types of radio codes can coexist simultaneously.
A maximum of 256 codes can be memorised.
The codes memorised act as an OPEN or CLOSE command.
The remote controls and the XF radio module must have
the same frequency.
When memorising the codes, keep the remote control
approximately one meter from the XF radio module.
1. (
46
) Insert the XF radio module in the connec-
tor J3 paying attention to the insertion direction
(imm.xx).
2. Memorise the remote controls.
!
Ensure that there are no obstacles (persons or things)
while the automation is moving.
SLH/SLH LR - MEMORISING THE FIRST REMOTE
CONTROL
1. Press and keep pressed the + key (OPEN program-
ming) or - (CLOSE programming). After pressing
the button for about 5 seconds, the corresponding
radio LED (DL4 or DL5) will start to flash to indicate
that the radio code learning phase has started.
2. Release the button. From this moment E614
stays in the learning phase for around 20 secs.
3. Press and hold down buttons P1 and P2 simultane-
ously on the SLH/SLH LR remote control (master
version only). The LED on the remote control
starts to flash.
4. Release both buttons; the LED on the remote
control continues to flash.
5. Make sure that the LED DL4 or DL5 on the board
is still flashing and press the button of the remote
control that you wish to memorise for a few sec-
onds (the LED becomes steady). Release the button
of the remote control.
6. Press the same button that was used in the pre-
vious step twice in succession to complete the
memorisation process. If the procedure was
carried out correctly, B614 opens, if permitted by
the operating mode that has been set.
SLH/SLH LR - MEMORISING OTHER REMOTE
CONTROLS
1. Press and hold down buttons P1 and P2 simulta-
neously on the SLH/SLH LR remote control that
has already been memorised (master version
only). The LED on the remote control starts to
flash.
2. Release both buttons; the LED on the remote
control continues to flash.
3. Press and hold down the button that has already
been memorised (the LED becomes steady).
4. Place the remote control that has already been
memorised close to the remote control to be
memorised (keeping the button in the previous
step pressed).
5. Press the button of the remote control to be
memorised and make sure that its LED flashes
twice before going off, to indicate that the proce-
dure was completed successfully.
6. Release all buttons.
7. Press the button used in step 5 twice in succession
to complete the memorisation process for the new
remote control. If the procedure was carried out
correctly, the B614 will open the barrier, if permit-
ted by the operating mode that has been set.
LC/RC - MEMORISING THE FIRST REMOTE
CONTROL
1. Press and keep pressed the + key (OPEN program-
ming) or - (CLOSE programming). After pressing
the button for about 5 seconds, the corresponding
radio LED (DL4 or DL5) will start to flash to indicate
that the radio code learning phase has started.
2. Release the button, from this moment E614 stays
in the learning phase for around 20 secs.
3. Make sure that the LED DL4 or DL5 on the board
is still flashing and press the button of the LC/RC
remote control that you wish to memorise for a
few seconds (the LED becomes steady). The LED
(DL4 or DL5) on the board goes on as a steady light
for 1 sec to then start flashing again for another 20
seconds during which it is possible to memorise
another remote control.
4. To memorise additional remote controls at a later
stage, repeat the procedure from the beginning
or carry out the remote memorisation procedure.
LC/RC - REMOTE CODE MEMORISATION
PROCEDURE
Additional remote controls can be memorised remote-
ly, i.e. without having to use the board directly, by us-
ing a remote control that has already been memorised.
1. Near the E614 press buttons P1 and P2 if the
remote control already memorised (as OPEN or
CLOSE at the same time). The LED of the remote
control and LED DL4 or DL5 of the board begin to
flash for 5 secs.
2. Release both the buttons then press the button
already memorised within five seconds. From
this moment E614 stays in the learning phase for
around 20 secs.